Vorsprung SolidCore Motor Mounts (Pair), Audi B8/B8.5 S4, S5, SQ5, A4, A5, Q5, C7 A6, A7, D4 A8
Vorsprung SolidCore motor mounts are solid, fluid-free replacement engine mounts for the Audi B8/B8.5 S4, S5, SQ5, A4, A5, allroad and Q5, the C7/C7.5 A6 and A7, and the D4 A8 3.0T, sold as a matched pair in TruComfort 45A (street) or TruSport 65A (track) with the active mount emulator built in.
Feel a buzz through the seat at every red light? A clunk every time you get back on the throttle? Your Audi B8 or B8.5 motor mounts are trying to tell you something. The factory mounts are fluid-filled hydraulic units, and with enough miles (and enough right foot) the rubber tears, the fluid leaks and the engine starts moving around like it has somewhere better to be.
SolidCore mounts replace them with a fluid-free rubber element in an aluminum housing: nothing to leak, nothing to collapse, and a built-in emulator so your car never misses the factory active mounts. Pick your durometer, TruComfort 45A for the street or TruSport 65A for the track, and get a matched pair, one for each side, at the same price either way.
Choose Your Durometer: TruComfort 45A or TruSport 65A
Durometer is rubber hardness on the Shore A scale. Higher numbers are firmer. Most solid street-grade motor mounts for this platform use about 50A rubber, and track grades go up to 65A. We built one softer than the usual street grade and one that matches the firmest track grade, then gave them the same price.
| TruComfort 45A (Street) | TruSport 65A (Track) | |
|---|---|---|
| Rubber hardness | 45A, softer than the typical 50A street grade | 65A, the same hardness as the firmest track grades |
| Feel | The softest solid mount we make, tuned to keep daily-driver vibration in check | Firm and connected; passes a little more vibration into the cabin |
| Engine movement | Far less than a tired factory mount | The least: engine held tight under load |
| Best for | Stock or lightly modified daily drivers | Tuned and pulleyed cars, hard launches, track days |
| Price (pair) | $299.99 | $299.99 |
Why Factory Audi B8 Engine Mounts Fail
From the factory, each side of the engine sits on a hydraulic mount. A rubber spring carries the weight while fluid moving between internal chambers damps vibration, and on many B8 and B8.5 cars a solenoid valve (N144 on the left, N145 on the right) lets the engine computer change how it damps. Clever. Comfortable. Mortal.
The rubber neck under the center plate tears, the fluid weeps out behind the heat shields, and the mount quietly stops holding the engine. Owners report failures anywhere from the high 30,000-mile range to well past 100,000 miles, sooner with added power. The dealer fix? Genuine mounts for a 2013-2016 S4 (8R0199381AD left, 8R0199381AE right) list around $570 per side, for the same fluid-filled design that just failed you. That's the Audi Tax in its purest form.
How SolidCore Motor Mounts Fix It
- ✅ Fluid-free, fully bonded rubber: no fluid to leak, no chambers to tear, and no polyurethane to fatigue and pack down.
- ✅ A revised mold where mounts actually fail: a molded relief pocket and raised side ribs replace the solid dome under the center plate, designed to spread load away from the neck where solid-dome mounts tear.
- ✅ Built-in plug-and-play emulator: plugs into the factory N144/N145 connectors on cars with active mounts. Zero warning lights, zero coding, zero modification.
- ✅ Aluminum housing with a laser-engraved Vorsprung Autowerk logo, bolting in where the factory mounts came out.
- ✅ Sold as a matched pair, so both sides share the load evenly.
- ✅ Lifetime warranty for the original owner when you buy direct from us.
What You'll Notice Right Away
- ✅ Less engine movement under acceleration, braking and shifts
- ✅ Cleaner, more predictable shifts on S tronic and manual cars
- ✅ Sharper throttle response and more direct power transfer
- ✅ A planted, connected feel between engine and chassis
- ✅ No more fluid leaks, ever
Bottom line: solid, leak-proof motor mounts in the firmness you want, with the active mount electronics handled, for $100 to $250 less than comparable name-brand pairs.
SolidCore vs Name-Brand vs Dealer Mounts
| Vorsprung SolidCore | Typical name-brand solid mounts | Dealer (genuine Audi) | |
|---|---|---|---|
| Construction | Fluid-free rubber in an aluminum housing | Solid rubber in a cast or billet body | Fluid-filled hydraulic with a solenoid valve |
| Hardness choices | 45A street or 65A track | Usually 50A street, 65A track | One factory feel |
| Active mount electronics | Emulator built in | On most; check each listing | Factory solenoid (N144/N145) |
| Price | $299.99 per pair | About $400 to $550 per pair | About $570 list per side |
Vehicle Fitment
SolidCore motor mounts fit the Audi B8 and B8.5 S4, S5 and SQ5 with the 3.0T supercharged V6, the B8/B8.5 A4, A5 and allroad with the 2.0T or 3.2L V6, and the B8/B8.5 Q5 with the 2.0T, 3.0T or 3.2L. They also fit the C7 and C7.5 A6 and A7 with the 2.0T or 3.0T supercharged V6, and the D4 A8 3.0T. Both durometers share the same fitment.
B8 and B8.5 cars run from the 2008 through 2016 model years. In North America the A5, S5, Q5 and SQ5 kept the B8.5 chassis for 2017 as well, so if you have a 2017, email your VIN and we'll confirm before you order.
| Make | Model | Chassis | Engine |
|---|---|---|---|
| Audi | S4, S5, SQ5 | B8 / B8.5 | 3.0T V6 Supercharged |
| Audi | A4, A5, allroad | B8 / B8.5 | 2.0T, 3.2L V6 |
| Audi | Q5 | B8 / B8.5 | 2.0T, 3.0T V6 Supercharged, 3.2L V6 |
| Audi | A6, A7 | C7 / C7.5 | 2.0T, 3.0T V6 Supercharged |
| Audi | A8 | D4 | 3.0T V6 Supercharged |
NOTE: Not for the B8 S5 or RS5 with the 4.2 V8, 3.0 TDI models, the 4.0T C7 S6, S7, RS6 and RS7, or B9-generation cars. Direct replacement for the factory fluid-filled mounts, no modification or tuning required. Not sure? Email your VIN to help@vorsprungautowerk.com and we'll confirm fitment.
Installation Notes
- ✅ Plan a few hours: about 4 to 5 hours for an experienced tech. You'll want an engine support bar, and many owners lower the front subframe roughly 25 to 35 mm for access.
- ✅ Plug in the emulators: connect the factory N144 and N145 plugs to the SolidCore connectors before the engine goes back down.
- ✅ Fresh hardware: owners recommend new factory stretch (torque-to-yield) bolts, torqued to factory spec.
- ✅ Alignment: if you lowered the subframe, mark its position first and get an alignment check afterward.
- ✅ Do it once: replace both sides and the transmission mount in the same visit.
Audi B8 and C7 Motor Mounts FAQ
Should I choose TruComfort 45A or TruSport 65A?
If the car is your daily and mostly stock, go TruComfort 45A. If it's tuned, pulleyed, launched hard or tracked, go TruSport 65A. Same price, same fitment, same warranty; only the rubber hardness changes.
Will these throw a check engine light or N144/N145 codes?
No. Each mount has a built-in emulator that plugs into the factory active mount connectors, so there are no warning lights and no coding.
Are solid motor mounts too harsh for a daily driver?
Not with the right durometer. TruComfort 45A is softer than the 50A rubber most street-grade solid mounts use. TruSport 65A passes a little more vibration into the cabin, which is the trade for maximum engine control.
Will these fit my Audi A4, S4, Q5, SQ5 or A6?
Yes, if it's a B8/B8.5 S4, S5, SQ5, A4, A5, allroad or Q5, a C7/C7.5 A6 or A7, or a D4 A8 3.0T. Check the fitment table above for your engine. They don't fit 4.2 V8, TDI, 4.0T or B9 cars.
What are the signs of bad Audi B8 or C7 motor mounts?
Vibration through the seat, steering wheel or shifter at idle in Drive, a clunk when you get on or off the throttle or on shifts, the engine visibly rocking when someone blips the throttle with the hood up, and fluid weeping from the mounts behind the heat shields. Notice two or more? Check the mounts before you chase anything else.
Do I need to replace both mounts?
Yes. Replacing only one side causes uneven load, faster wear on the new mount and poor drivetrain alignment. That's why SolidCore is sold as a pair.
How do these compare to name-brand street and track solid mounts?
Same idea, solid rubber in an aluminum body with an emulator, at a better price. TruComfort 45A is softer than the typical 50A street grade, TruSport 65A matches the firmest track grade, and a pair is $299.99 versus about $400 to $550 for comparable name-brand pairs, with a lifetime warranty for the original owner.
What's the difference between the SolidCore and DynaCore TruSport 65A?
The DynaCore TruSport 65A wraps 65A rubber around a tuned fluid core to absorb high-frequency vibration, and current stock is discounted for minor cosmetic paint defects. SolidCore TruSport 65A is fully solid rubber with nothing inside to leak.
What's the warranty?
A lifetime warranty for the original owner when purchased through vorsprungautowerk.com, covering defects in materials and workmanship. If a mount fails under normal use, we repair or replace it at no charge. Proof of purchase and return of the original part for inspection are required, and standard shipping rates apply to replacements.
Why Buy From Us?
Two durometers, one honest price, the active mount electronics already handled and a lifetime warranty for the original owner. Both versions are in stock and ship from us, and a real person will check your VIN before you order.
-
✅
Enthusiast Designed & Tested: Developed by people who actually drive and modify these cars.
-
✅
Tested on Our Own Cars: If we wouldn't run it ourselves, we don't sell it.
-
✅
Continuous R&D: We continually develop and improve our products instead of relying on generic catalog parts.
-
✅
Supporting Audi Platform Development: Your purchase helps fund continued development of new parts for these chassis.
-
✅
Real Enthusiast Support: Get help from people who understand the platform, not ticket bots.
-
✅
Small Team, Big Passion: Every order directly supports continued product development and innovation.
-
✅
Performance Without the Marketing Fluff: Purpose-built parts designed to perform.
Complete Your Build
The car is already apart. Finish the drivetrain while you're under there:
- TruShift Transmission Upgrade Mount (B8/B8.5): 65 durometer rubber at the back of the gearbox, so the whole drivetrain stops moving, not just the front.
- Billet Subframe Inserts (B8/B8.5): fill the voids in the factory subframe mounts for sharper steering response.
- Billet Rear Differential Carrier Inserts (B8/B8.5, C7): firm up the rear of the driveline to match.
- TruShift Mount Upgrade V2 (C7/C7.5 A6, A7): the transmission mount upgrade for C7 owners.
- Billet Subframe Inserts (C7 A6, A7): the subframe insert set for the C7 chassis.
Still deciding? Our Audi B8 S4 engine mounts guide covers failure signs, cost and how to choose, and the engine and transmission mounts collection has every option in one place.
Shop More Parts for Your Audi
Browse every Vorsprung part for your chassis: Audi S4 & S5 B8/B8.5 parts · Audi Q5 & SQ5 B8/B8.5 parts · Audi A6 & A7 C7/C7.5 parts · Audi A8 D4 parts.
Drive the difference. Drive Vorsprung.
Vorsprung SolidCore Motor Mounts (Pair), Audi B8/B8.5 S4, S5, SQ5, A4, A5, Q5, C7 A6, A7, D4 A8
Frequently Asked Questions (FAQ)
What types of products do you offer?
We offer a wide range of high-performance automotive parts including engine components, suspension upgrades, fueling solutions, and custom wheels, all designed to enhance your vehicle’s performance.
Are your products compatible with all car models?
Our products are specifically designed for high-performance vehicles, including luxury and sports cars like Audi. For compatibility details, please refer to the product description or contact our support team for assistance.
How can I ensure the correct fit for my car?
We offer guided fitment assistance for all our products. If you're unsure, feel free to reach out to our customer support team, and we'll help you find the perfect fit for your vehicle.
Where do you ship?
We currently ship to the United States and Canada, with free US shipping on orders over $425. Outside North America? Email orders@vorsprungautowerk.com with your part and address and we'll quote shipping for you.
How do I install the products?
Most of our products come with easy-to-follow installation guides. Additionally, if you need professional installation, we can recommend certified mechanics or shops for assistance.
What is your return policy?
We offer a 14-day return policy for unused products. To be eligible for a return, items must be in their original packaging and in resellable condition. Please refer to our return policy page for detailed instructions.
How can I contact customer support?
You can contact our customer support team via email at orders@vorsprungautowerk.com or through the chat button on the website.
Precision Forged Custom Wheels
At Vorsprung Autowerk, we offer the perfect blend of strength, performance, and style with our custom wheels. Crafted using the finest materials and advanced engineering techniques, our wheels are built to enhance your vehicle's handling and aesthetics.
Key Features
- Monoblock or Multipiece Design
- Custom Spoke Design
- Perfect Fitment Guaranteed
- Multiple Color & Finish Options
- Aircraft-Grade 6061 Aluminum
- Precision Forged for Durability