Vorsprung Audi 3.0T Oil Filter Housing Conversion, Billet Spin-On (EA837 Supercharged)
Audi EA837 3.0T Oil Filter Housing Conversion, Billet Spin-On
Break Up With Your Cartridge Filter
Audi decided your oil filter should live inside a plastic housing that turns into a science experiment after a few thousand heat cycles: warped, cracked, and occasionally weeping oil onto your driveway like a bad breakup. The cartridge filter inside doesn't help matters either, its anti-drain back valve eventually taps out, so your engine spends a few extra seconds every cold start wondering where all its oil pressure went. The Vorsprung Autowerk Oil Filter Housing Conversion ends that relationship for good.
No more chasing leaks around the housing. Convert once, and never think about it again (we mean that in a good way).
- ✅ Spin-on oil filter conversion for the Audi 3.0T EA837 supercharged V6, running Mann W719/45, Hengst H14W30 or Audi 06J115403Q filters
- ✅ CNC-machined 6061 billet aluminum, replacing the plastic 06E115405K, 06E115405A and 06E115405C housings
- ✅ Retains the OEM mounting design and reuses your OEM hardware
- ✅ TruSeal peroxide-cured FKM gasket included, so the seal lasts as long as the billet
- ✅ $224.99 pre-order pricing, shipping late November 2026
Billet spin-on conversions for this engine commonly sell for around $350. Ours is $224.99, with a TruSeal gasket in the box.
Built to End the Cartridge Era
Rather than patching the factory cartridge design, we converted it entirely. This kit swaps your OEM cartridge housing for a CNC-machined billet aluminum unit that runs a proven spin-on canned filter instead, the same filter technology trusted across nearly every other engine platform for a reason.
CNC-Machined 6061 Aluminum Housing
Machined from solid 6061 aluminum rather than molded plastic, this housing resists the heat cycling that warps and cracks the factory unit. It reuses your OEM hardware and ships with our TruSeal gasket, so the whole conversion goes on without hunting for a single bolt.
Keeps the OEM Mounting Design
Our housing retains Audi's original mounting design: same mounting points, same orientation, same OEM hardware. Not every billet conversion on the market does. Some change the mounting layout, which means more to check during the install and more to think about the next time the housing comes off. Ours goes back exactly where the factory housing came out.
TruSeal Gasket Included, Because Billet Deserves Better
A billet housing is great, until the gasket under it has the same service life as the plastic part you just replaced. Many billet conversions still seal with a standard factory-spec gasket, and that gasket is what eventually hardens, flattens and starts weeping again. Every Vorsprung conversion ships with our TruSeal oil filter housing gasket instead:
- ✅ Peroxide-cured FKM that resists the amine additives in modern synthetic oils, the chemistry that hardens factory seals over time
- ✅ Stays flexible down to -40°F, so it keeps sealing on a sub-zero cold start instead of pulling away from the housing
- ✅ 75 Shore A durometer, specced to seal against billet aluminum without extruding under oil pressure spikes
The housing is built to outlast the engine. Now the seal is too.
A Fresh Anti-Drain Back Valve, Every Oil Change
Because the valve lives inside the spin-on filter can itself, you get a brand new anti-drain back valve every single oil change. No more wondering whether a tired valve left your engine starving for oil pressure on startup.
Direct Bolt-On, No Engine Mods
This conversion bolts straight to your factory mounting points and accepts widely available spin-on filters, including Mann W719/45 and Hengst H14W30, so future oil changes stay simple at any shop.
Factory Cartridge Housing vs Vorsprung Spin-On Conversion
| Factory Cartridge Housing | Vorsprung Spin-On Conversion | |
|---|---|---|
| Housing material | Molded plastic | CNC-machined 6061 billet aluminum |
| Filter | Cartridge element inside the housing | Spin-on canned filter (Mann W719/45, Hengst H14W30, Audi 06J115403Q) |
| Anti-drain back valve | Ages with the cartridge system | New valve in every spin-on filter |
| Gasket | Factory-spec seal | TruSeal peroxide-cured FKM, included |
| Mounting | OEM mounting points | Same OEM mounting design and hardware |
Key Features & Specifications
-
Material: CNC-Machined 6061 Billet Aluminum
-
Mounting: Retains the OEM Mounting Design and Factory Mounting Points
-
Hardware: Accepts all OEM hardware
-
Gasket: Vorsprung TruSeal Peroxide-Cured FKM Gasket, Included
-
Filter System: Converts Cartridge to Spin-On Canned Filter
-
Compatible Filters: Mann W719/45, Hengst H14W30, Audi 06J115403Q
-
Replaces OEM Part Numbers: 06E115405K, 06E115405A, 06E115405C
-
Fitment: Direct Bolt-On OEM Replacement, No Engine Modifications Required
Bottom line: a billet housing that bolts on like the factory part, with a gasket built to last as long as the billet.
Vorsprung Autowerk Guarantee: Once this conversion is on your engine, the factory cartridge housing is a problem you'll never think about again.
Vehicle Fitment
This Audi 3.0T oil filter housing conversion fits the supercharged EA837 V6 that uses the 06E115405K, 06E115405A or 06E115405C cartridge housing: the 2010-2016 S4 (B8/B8.5), 2010-2017 S5 (B8/B8.5), 2013-2017 Q5 3.0T and 2014-2017 SQ5 (8R, often called B8.5), 2009-2011 A6 3.0T (C6), 2012-2015 A6 and A7 (C7), 2013-2014 A8 3.0T (D4) and 2011-2015 Q7 3.0T (4L), plus the European-market B8.5 A4 and A5 3.0 TFSI. It does not fit Gen 2 CREC cars: the 2017-2019 Q7 (4M), the 2016-2018 A6 and A7 (C7.5) or the 2015-2018 A8.
| Make | Model | Years | Chassis | Engine |
|---|---|---|---|---|
| Audi | S4 | 2010-2016 | B8 / B8.5 | 3.0 TFSI Supercharged |
| Audi | S5 | 2010-2017 | B8 / B8.5 | 3.0 TFSI Supercharged |
| Audi | Q5 3.0T | 2013-2017 | 8R (B8.5) | 3.0 TFSI Supercharged |
| Audi | SQ5 | 2014-2017 | 8R (B8.5) | 3.0 TFSI Supercharged |
| Audi | A6 3.0T | 2009-2011 | C6 | 3.0 TFSI Supercharged |
| Audi | A6 3.0T | 2012-2015 | C7 | 3.0 TFSI Supercharged |
| Audi | A7 3.0T | 2012-2015 | C7 | 3.0 TFSI Supercharged |
| Audi | A8 3.0T | 2013-2014 | D4 | 3.0 TFSI Supercharged |
| Audi | Q7 3.0T | 2011-2015 | 4L | 3.0 TFSI Supercharged |
| Audi | A4 (non-US market) | 2012-2015 | B8.5 | 3.0 TFSI Supercharged |
| Audi | A5 (non-US market) | 2012-2016 | B8.5 | 3.0 TFSI Supercharged |
NOTE: Fits the Gen 1 EA837 3.0 TFSI supercharged engine only. It does not fit Gen 2 CREC cars (2017-2019 Q7 4M, 2016-2018 A6 and A7 C7.5, 2015-2018 A8) or the EA839 2.9T/3.0T twin-turbo engine. Not sure which housing your car has? Email your VIN to help@vorsprungautowerk.com and we will confirm before you order.
S5 / A5 NOTE: 2010-2012 fitment is the S5 Cabriolet only (the 2008-2012 S5 coupe has the 4.2 V8). The A5 was never sold with the supercharged 3.0T in North America.
Convert to a filter system built to outlast your engine, and stop thinking about your oil filter housing altogether.
Audi EA837 Oil Filter Housing Conversion FAQ
Will this work with my existing oil filter?
No, this converts your factory cartridge housing to a spin-on canned filter system. Once installed, use Mann W719/45, Hengst H14W30, or Audi 06J115403Q filters instead of the cartridge element.
Which OEM oil filter housing part numbers does this replace?
It replaces the plastic Audi 3.0T cartridge housings 06E115405K, 06E115405A and 06E115405C. If your housing carries one of those numbers and your engine is the supercharged EA837, this conversion is a direct swap.
Do I need any special tools to install it?
No, it bolts to the factory mounting points with standard hand tools, reusing your OEM hardware. Our TruSeal gasket is included.
How is this different from other billet oil filter housing conversions?
Two ways. It keeps the OEM mounting design, so it bolts to the factory mounting points with your OEM hardware instead of a changed layout. And it ships with our TruSeal peroxide-cured FKM gasket rather than a standard factory-spec seal, so the gasket lasts as long as the billet housing it seals.
Does this fit the EA839 2.9T/3.0T twin-turbo engine?
No, this conversion is designed specifically for the EA837 3.0 TFSI supercharged engine.
Does it fit the Gen 2 (CREC) supercharged 3.0T?
No. This conversion fits the Gen 1 EA837 only. It does not fit Gen 2 CREC cars: the 2017-2019 Q7 (4M), the 2016-2018 A6 and A7 (C7.5) or the 2015-2018 A8.
What oil filter should I run after installing this?
Any standard spin-on filter that fits the Mann W719/45 / Hengst H14W30 spec, including the OEM-equivalent Audi 06J115403Q.
Why does the factory Audi 3.0T oil filter housing leak?
The plastic housing warps and cracks after years of heat cycling, and the factory gasket hardens and flattens until it starts weeping oil. Our oil filter housing gasket guide walks through the leak signs and causes.
Can I just replace the gasket instead?
Yes, if the housing itself is still straight and uncracked. Our TruSeal gasket fits the factory housing, a replacement EA837 oil filter housing covers a warped or cracked one, and our step-by-step replacement guide covers the job. The conversion is for owners who want to retire the cartridge design for good.
When will my order ship?
This is a pre-order. Stock arrives late November 2026, and pre-order pricing holds until then, so ordering now locks in today's price.
Complete Your Build
- SAI Delete Plate Set - removing the secondary air system opens up access to the oil filter housing area (off-road use, tune required).
- TruSeal Oil Gasket Upgrade - a spare TruSeal housing gasket for future service, plus PCV and intake manifold seals in the same compound.
Why Buy From Us?
A billet housing that keeps the factory mounting design, plus a TruSeal gasket in the box so the seal is not the weak link. It ships from us, and a real person will confirm fitment before you order.
-
✅
Enthusiast Designed & Tested: Developed by people who actually drive and modify these cars.
-
✅
Tested on Our Own Cars: If we wouldn't run it ourselves, we don't sell it.
-
✅
Continuous R&D: We continually develop and improve our products instead of relying on generic catalog parts.
-
✅
Supporting Audi Platform Development: Your purchase helps fund continued development of new parts for these chassis.
-
✅
Real Enthusiast Support: Get help from people who understand the platform, not ticket bots.
-
✅
Small Team, Big Passion: Every order directly supports continued product development and innovation.
-
✅
Performance Without the Marketing Fluff: Purpose-built parts designed to perform.
Shop More Parts for Your Audi
Browse every Vorsprung part for your chassis: Audi S4 & S5 B8/B8.5 parts · Audi A6 & A7 C7 parts · Audi A6 C6 parts · Audi A8 D4 parts · Audi Q5 & SQ5 B8/B8.5 parts · Audi Q7 parts. Or see all Audi 3.0T performance parts.
Drive the difference. Drive Vorsprung.
Vorsprung Audi 3.0T Oil Filter Housing Conversion, Billet Spin-On (EA837 Supercharged)
Frequently Asked Questions (FAQ)
What types of products do you offer?
We offer a wide range of high-performance automotive parts including engine components, suspension upgrades, fueling solutions, and custom wheels, all designed to enhance your vehicle’s performance.
Are your products compatible with all car models?
Our products are specifically designed for high-performance vehicles, including luxury and sports cars like Audi. For compatibility details, please refer to the product description or contact our support team for assistance.
How can I ensure the correct fit for my car?
We offer guided fitment assistance for all our products. If you're unsure, feel free to reach out to our customer support team, and we'll help you find the perfect fit for your vehicle.
Where do you ship?
We currently ship to the United States and Canada, with free US shipping on orders over $425. Outside North America? Email orders@vorsprungautowerk.com with your part and address and we'll quote shipping for you.
How do I install the products?
Most of our products come with easy-to-follow installation guides. Additionally, if you need professional installation, we can recommend certified mechanics or shops for assistance.
What is your return policy?
We offer a 14-day return policy for unused products. To be eligible for a return, items must be in their original packaging and in resellable condition. Please refer to our return policy page for detailed instructions.
How can I contact customer support?
You can contact our customer support team via email at orders@vorsprungautowerk.com or through the chat button on the website.
Precision Forged Custom Wheels
At Vorsprung Autowerk, we offer the perfect blend of strength, performance, and style with our custom wheels. Crafted using the finest materials and advanced engineering techniques, our wheels are built to enhance your vehicle's handling and aesthetics.
Key Features
- Monoblock or Multipiece Design
- Custom Spoke Design
- Perfect Fitment Guaranteed
- Multiple Color & Finish Options
- Aircraft-Grade 6061 Aluminum
- Precision Forged for Durability