Audi 3.0T Tech Guides & News

Audi 3.0T Injector Seals: Leak Signs, Gen 1 vs CREC Kits and a Leak-Free Install (S4, S5, Q5, SQ5, A6, A7, A8, Q7)

Audi 3.0T injector seals: Elring 06E998907E fuel injector repair kit for the Gen 1 S4, S5, Q5, SQ5, A6, A7 and Q7

Pulled the supercharger for a PCV valve, thermostat or water pump, then watched an injector come out stuck in the lower intake manifold? Congratulations: you now need new Audi 3.0T injector seals. The PTFE ring at the tip of a direct injector does not seal twice, and a weeping O-ring at the fuel rail sits right under a hot supercharger. The fix is cheap if you do it once: our Elring 06E998907E injector seal kit for the Gen 1 Audi 3.0T is $12.95 per injector. Here is how to spot a leak, pick the right kit and install it without a comeback.

Short answer: every time a 3.0T injector comes out, it gets a new PTFE combustion seal and O-ring. Gen 1 engines take 06E998907E, one kit per injector, and CREC engines take 06E998907F. The seals are cheap. Pulling the supercharger twice is not.

What Audi 3.0T Injector Seals Actually Do

Your supercharged 3.0T (EA837) has six direct injectors, each seated in the cylinder head under the lower intake manifold and fuel rail, all under the supercharger. Each relies on a small stack of seals:

  • ✅ The O-ring at the fuel rail end holds back high-pressure fuel. Audi's workshop manual warns that this system runs at extremely high pressure and must be bled down before it is opened.
  • ✅ The PTFE (Teflon) combustion seal at the tip holds combustion pressure in the cylinder.
  • ✅ Support rings, spacers and clips keep the injector square in its bore.

PTFE shrugs off heat, but it does not spring back like rubber. Audi's procedure stretches each new ring over an assembly cone, then shrinks it back down with two calibration sleeves. Once a ring has been seated and pulled, its job is done. That is why Audi's manual calls for a new sealing element, combustion chamber seal and O-ring whenever an injector is removed, and industry guidance agrees the combustion seal cannot be reused in most applications.

Where the Audi 3.0T injector seals live Simplified side section of one Audi 3.0T direct injector: the supercharger on top, the lower intake manifold and fuel rail below it, the injector in the cylinder head with an O-ring at the fuel rail end and a PTFE combustion seal at the tip, and the combustion chamber below. AUDI 3.0T INJECTOR SEALS SIDE SECTION, ONE INJECTOR SUPERCHARGER LOWER INTAKE MANIFOLD FUEL RAIL CYLINDER HEAD 1 2 3 4 5 1 2 3 4 5 SUPERCHARGER LOWER MANIFOLD + RAIL RAIL O-RING PTFE COMBUSTION SEAL COMBUSTION CHAMBER INJECTOR OUT comes off first pressed onto the injectors seals high-pressure fuel seals combustion pressure fuel sprays in here means new seals, every time SCHEMATIC ONLY, NOT TO SCALE.
Simplified side section: the supercharger and lower intake manifold come off before any injector does, and each injector seals fuel at the rail and combustion pressure at the tip.

Symptoms of Leaking 3.0T Injector Seals

  • ✅ A raw fuel smell from the engine bay, especially after valley work. One 2014 S4 owner traced exactly that to injector O-rings under the supercharger.
  • ✅ Fuel in the valley. Another owner found the valley under the supercharger flooded with fuel after a PCV job because two injector seals had torn.
  • ✅ A misfire that stays on one cylinder after a coil and plug swap. Our Audi ignition coil replacement guide covers that swap test.
  • ✅ Trouble that started right after PCV, thermostat or water pump work, when injectors get disturbed.
  • ✅ A leak you cannot see: hot gas escaping past a bad tip seal can cook the injector's plastic parts and costs efficiency.

Smell raw fuel? Park it. Gasoline on a hot engine is not a next-weekend problem.

When Audi 3.0T Injector Seals Must Be Replaced

Rule one: if an injector comes out, it gets new seals. The catch: injectors sometimes come out uninvited.

  • ✅ Valley jobs. PCV and breather work means pulling the lower intake manifolds. The injectors should stay in the head, but owners report them riding out with the manifold: one 2014 A6 3.0T owner had all three on one bank come out, and another had two of three come out during a PCV job. Our Audi 3.0T PCV valve replacement guide walks through that teardown.
  • ✅ Injector service. Injectors pulled for ultrasonic injector cleaning and flow testing, or for replacements, go back with fresh seals.
  • ✅ Leak or misfire hunting. If the trail leads to one injector, reseal it before you condemn it.

The Real Cost Is the Labor

Seals are cheap. Pulling the supercharger is not. Owner-reported dealer quotes for supercharger-off PCV repairs on the SQ5 came in around $730 CAD and $815, and one 3.0T owner was quoted $1,500 by a dealer to replace a single injector, $697 of it in parts. If the injectors move during a valley job, reseal all six now. Paying for that labor twice is the most expensive way to save $13.

What to Look For in an Audi 3.0T Injector Seal Kit

  • ✅ The right part number: 06E998907E for Gen 1, 06E998907F for CREC
  • ✅ A new PTFE combustion seal for every injector you pull
  • ✅ Fresh upper seals too, since Audi renews the O-ring and sealing element on every removal
  • ✅ Six sets, because a V6 has six injectors
  • ✅ A known OE-supplier brand behind the seals
  • ✅ The sizing tools lined up before you start
  • ✅ A VIN check if your car sits near a model-year changeover

Vorsprung vs Typical Aftermarket vs Genuine Audi Seal Kits

In short: our genuine Elring 06E998907E kit is $12.95 per injector, or $77.70 for all six on a Gen 1 engine. Typical aftermarket kits sell for about $9 to $11 each, or about $55 to $66 for six. Genuine Audi kits list around $31 each, roughly $185 for six, and some sellers ask $40 to $57 apiece. That is the Audi Tax on a handful of rings. CREC owners get all six injectors covered in one box for $59.99.

Vorsprung Elring 06E998907E Typical aftermarket kits Genuine Audi kits
Price per injector $12.95 About $9 to $11 About $31 at list, up to about $57 at some sellers
All six injectors $77.70 About $55 to $66 About $185 or more
Who makes the seals Elring, a longtime OE sealing supplier Varies by brand Audi
In a valley kit Six sets in every Vorsprung under supercharger kit Varies by kit Ordered per injector at the parts counter
Fitment help VIN check by email Varies by seller Dealer parts counter

Want OE-supplier seals without dealer pricing? Order six of our Elring 06E998907E Audi 3.0T injector seal kits and reseal the whole engine in one visit.

Shop the Elring 06E998907E Kit, $12.95

✅ Elring seals, plus Graf and Hengst in our valley kits  ·  ✅ Fitment help by VIN at help@vorsprungautowerk.com  ·  ✅ Free US shipping on orders over $425

What Is in Our Audi 3.0T Injector Seal Kits

  • ✅ Gen 1, Elring 06E998907E injector repair kit ($12.95): a fuel injector gasket and a Teflon seal for one injector. Genuine Elring, sold individually, so order six for a V6.
  • ✅ CREC, 06E998907F fuel injector reseal kit ($59.99): high-temp Viton O-rings, PTFE combustion seals, support spacers and tension clips for all six injectors.
  • ✅ Valley kits: every Vorsprung under supercharger kit includes six Elring injector seal kits (06E998907E in the Gen 1 kits, 06E998907F in the CREC kit) plus upper and lower intake manifold gaskets.

Elring 06E998907E fuel injector seal kit for the Audi 3.0T Gen 1 S4, S5, Q5, SQ5, A6, A7 and Q7, one injector's worth of seals

Injectors dirty rather than dead? Our injector rebuild service does ultrasonic cleaning and flow testing, listed from $25 per direct injector. It shows as unavailable online right now, so email help@vorsprungautowerk.com before you ship anything. Shopping for bigger injectors? Read our guide to 550cc injectors and direct injection first.

Audi 3.0T Injector Seal Fitment: Gen 1 vs CREC

Gen 1 EA837: our Elring 06E998907E kit is listed for the B8 and B8.5 S4 (2010 to 2016), the S5 (2010 to 2012 Cabriolet only, then 2013 to 2017), the Q5 3.0T (2013 to 2017), the SQ5 (2014 to 2017), the C6 and C7 A6 (2009 to 2015), the C7 A7 (2012 to 2015) and the 4L Q7 3.0T.

CREC and CREH: our 06E998907F fuel injector reseal kit for the CREC 3.0T is listed for the 2016 to 2018 A6 and A7, the 2015 to 2018 A8 and the 2017 to 2018 Q7.

06E998907F fuel injector reseal kit for the Audi 3.0T CREC A6, A7, A8 and Q7, showing one injector's seals, spacer and clip

Car not listed, like a 2013 or 2014 A8 3.0T or a 2019 Q7? Email your VIN to help@vorsprungautowerk.com and we will confirm the right kit. Unsure of your engine? Our Audi 3.0T Gen 1 vs CREC engine guide explains it. Both kits are listed for the supercharged 3.0T only, not the turbocharged EA839 in the B9 S4.

Install Notes for Audi 3.0T Injector Seals

Time: the supercharger and the lower intake manifold on each bank come off first. A popular DIY guide for the same teardown says to set aside a full day, and owners say a skilled tech needs about 3 hours for supercharger-off work while DIYers should plan on 5 or more. Then add time to pull, reseal and seat six injectors.

Tools: Audi's procedure uses the T10133 FSI tool set: puller T10133/2A with removal tool T10133/16, nylon bore brush T10133/4, assembly cone T10133/5, assembly sleeve T10133/6, calibration sleeves T10133/7 and T10133/8, and installer T10133/9.

  • ✅ Bleed off fuel pressure first, and keep the driver's door shut once lines are loose, since opening it can prime the pump.
  • ✅ Label every injector by cylinder before it comes out.
  • ✅ Cut the old PTFE ring off without nicking the groove. Audi says a damaged groove means a new injector.
  • ✅ Clean each bore with a nylon brush.
  • ✅ Fit each new PTFE seal with the cone and sleeve, then size it with both calibration sleeves using a push and a half turn.
  • ✅ Keep the PTFE seal dry. Only the O-ring gets a light film of clean engine oil.
  • ✅ If an injector will not slide in easily, wait for the seal to shrink. Do not force it.
  • ✅ Prime the system and check for leaks before the supercharger goes back on.

Doing the valley anyway? Our B8.5 under supercharger kit ($649.99 to $719.99, for the B8.5 S4, S5, Q5, SQ5 and 2013 to 2014 A8) bundles six Elring injector seal kits, upper and lower intake manifold gaskets, a Hengst PCV valve, a Graf water pump and a billet thermostat housing. B8, C7, 4L Q7 and CREC versions live in our under supercharger kits collection.

OE Ultimate Under Supercharger Kit for the Audi 3.0T Gen 1 B8.5 S4, S5, Q5 and SQ5 with injector seals, intake manifold gaskets, water pump and PCV valve

Audi 3.0T Injector Seals FAQ

Do you have to replace injector seals every time you remove an injector?

Yes. Audi's workshop procedure for the 3.0 TFSI calls for a new sealing element, combustion chamber seal and O-ring whenever an injector comes out, and a PTFE combustion seal cannot seal again once it has been seated and pulled.

What is the difference between 06E998907E and 06E998907F?

Our listings use 06E998907E for the Gen 1 supercharged 3.0T and 06E998907F for the CREC and CREH engines in the 2016 to 2018 A6 and A7, 2015 to 2018 A8 and 2017 to 2018 Q7. Our E kit services one injector, while our F kit covers all six.

Do you have to remove the supercharger to replace Audi 3.0T injector seals?

Yes. Audi's procedure removes the supercharger and then the lower intake manifold on that bank before the injectors come out, so most owners reseal injectors during PCV, thermostat or water pump work.

Can you install the PTFE combustion seals without special tools?

Not reliably. Audi's procedure fits each seal with an assembly cone and sleeve, shrinks it back to size with two calibration sleeves and seats the injector with an installer. Our CREC kit listing also says a seal sizing tool is required.

How do I know if my 3.0T injector seals are leaking?

Watch for a raw fuel smell, fuel in the valley under the supercharger or a misfire that stays on one cylinder after a coil and plug swap, especially right after valley work. If you smell fuel, stop driving and find the leak.

How much does it cost to replace 3.0T injector seals?

Parts are cheap: $77.70 for six of our Elring kits on a Gen 1 engine or $59.99 for our CREC kit. Labor is the big number because the supercharger has to come off, and one owner was quoted $1,500 by a dealer to replace a single injector.

Should I replace injector seals during a PCV valve or thermostat job?

If any injector moves or comes out with the lower intake manifold, yes, and owners report exactly that happening. Every Vorsprung under supercharger kit already includes six Elring injector seal kits.

Bottom Line on Audi 3.0T Injector Seals

Audi 3.0T injector seals are the cheapest part of any job that disturbs the injectors and the most expensive part to get wrong. Replace them every time an injector moves, match the kit to your engine and size the PTFE rings properly. Gen 1 owners, grab six of our Elring 06E998907E injector seal kits for the Audi 3.0T. CREC owners, the six-injector 06E998907F kit has you covered. More fuel system parts live in our Audi fueling solutions collection.

Shop Audi 3.0T Injector Seals, $12.95

Drive the difference. Drive Vorsprung.

Prices checked October 28, 2026 and subject to change. Labor and repair figures are owner-reported or typical shop quotes, not Vorsprung pricing.

Previous
Intercooler Hose Silicone: Specs, Fitment and Heat Limits
Next
Audi Cat Converter Paths for EA837 and EA825