Your supercharged 3.0T pulls hard on the first run, softer on the second and like it packed a picnic by the third. Sound familiar? That is heat soak, and one of the most affordable places to fight it is the small electric pump that moves coolant through the supercharger's intercoolers. An Audi CWA-100 coolant pump upgrade replaces the factory Pierburg CWA-50 with a pump rated to push harder against the loop's resistance. Our CWA-100 coolant pump upgrade comes as a genuine Pierburg CWA-100-3 or our own Vorsprung VWA-100, and EA837 owners get the adapter harness in our 3.0T pump and harness kit.
One clarification: this is not the engine's main water pump. That one lives under the supercharger and has its own Audi 3.0T water pump replacement guide.
How the Supercharged 3.0T Intercooler Loop Works
Audi's training guide for this engine, Self-Study Programme 437 (written for the 3.0 TFSI's launch in the C6 A6), describes a tidy system. Two intercooler cores, one per cylinder bank, sit in parallel inside the supercharger housing. An electric centrifugal pump that Audi calls V188 pushes hot coolant from those cores to a low-temperature radiator at the front of the car, ahead of the engine radiator, and cooled coolant returns for another lap.
- Separate circuit, shared tank. The loop runs apart from the engine circuit but shares its expansion tank (more in our air to water intercooler explainer).
- The ECU runs it on demand, switching it on from a stored map based on charge pressure and temperature, then setting its speed with a PWM signal.
- It is not self-priming. A centrifugal pump must never run dry.
- Failure is quiet. If the pump fails, the ECU stores a fault and cuts engine output if charge air gets too hot. Audi notes that no warning lamp comes on.
So a tired pump never lights up the dash. The car just gets slower when it is hot, and most owners blame the weather.
Signs Your 3.0T Needs a CWA-100 Coolant Pump Upgrade
Is the loop your bottleneck? Log it first with our intake air temperature gauge guide, then look for these:
- ✅ Power fades after back-to-back pulls and takes its time coming back.
- ✅ Intake temperatures stay high in traffic or heat instead of settling toward ambient.
- ✅ A stored intercooler pump fault with no warning light.
- ✅ Silence during an output test. A working pump hums and vibrates; a dead one does nothing.
- ✅ You added heat with a tune, a smaller crank pulley or a ported supercharger.
- ✅ You fitted a bigger heat exchanger, which adds volume and some restriction for the stock pump to fight.
Rule out low coolant first: the loop shares the engine's expansion tank, so any leak can starve it (see our intercooler leak symptoms guide).
CWA-50 vs CWA-100: What Really Changes
Owners and our kit listing identify the factory pump as a Pierburg CWA-50. Here are Pierburg's published ratings:
- CWA-50 (factory): up to 24 L/min, up to 0.6 bar, under 6.5 A at 12 V.
- CWA-100: up to 30 L/min, up to 0.9 bar, under 9 A at 12 V.
Now look at the pressure line. Every core, hose and bend pushes back, and a centrifugal pump flows less the harder it has to push. The CWA-50 runs out of push at 0.6 bar, while the CWA-100 keeps going to 0.9 bar. In a restrictive loop, that headroom is the difference between moving coolant and barely moving it.
What a pump cannot do is add cooling capacity. It carries heat forward faster, but the front radiator still has to shed it, so on a stock core the gain shows up mostly as quicker recovery between pulls. Pair it with more core volume, as our Audi heat exchanger upgrade guide explains, and each part makes the other better. Our auxiliary radiator guide covers how the low-temp loop differs from the engine loop.
What to Look for in a CWA-100 Upgrade
- ✅ The right spec: a genuine Pierburg CWA-100-3, or an equivalent flow-tested to the same spec.
- ✅ A plug-and-play harness. The CWA-100-3 does not plug into the factory CWA-50 connector on its own.
- ✅ Factory PWM control, with no tune and no cut wires.
- ✅ Factory mounting in the stock location and Pierburg-style cushion clamp.
- ✅ Honest Gen 1 and CREC fitment. Some kits use a different harness for CREC engines.
- ✅ VIN-level fitment help from people who know the platform.
- ✅ A sane price. It is a pump and a short harness, not a family heirloom.
Our Kit vs Typical Name-Brand Kits vs a Factory Pump
Short version: our CWA-100 pump and harness kit is $199.99 with the Vorsprung VWA-100 or $309.99 with a genuine Pierburg CWA-100-3, harness included. Typical name-brand kits with a genuine CWA-100-3 and harness run about $375 to $400. A like-for-like factory pump? You pay the Audi Tax to get back the same CWA-50 flow.
| Feature | Vorsprung kit | Typical name-brand kit | Factory CWA-50 pump |
|---|---|---|---|
| Pump | Vorsprung VWA-100 or genuine Pierburg CWA-100-3 | Genuine Pierburg CWA-100-3 in most kits | CWA-50, the pump the car left the factory with |
| Pierburg rating | CWA-100 class: up to 30 L/min and 0.9 bar | Same CWA-100 rating | Up to 24 L/min and 0.6 bar |
| Rated current at 12 V | Under 9 A | Under 9 A | Under 6.5 A |
| Harness | Plug-and-play adapter to the factory CWA-50 connector, included | Included; some kits use a separate CREC version | Plugs straight in |
| Control | Factory PWM signal, no tune required per our listing | Factory PWM signal | Factory PWM signal |
| Price | $199.99 (VWA-100) or $309.99 (Pierburg); pump only from $179.99 | About $375 to $400 | Varies by part number; buys back stock flow |
Ready to move more heat? The Audi CWA-100 coolant pump upgrade starts at $179.99 for the pump alone.
Shop the CWA-100 Coolant Pump Upgrade, from $179.99
✅ Genuine Pierburg CWA-100-3 option · ✅ Fitment help by VIN at help@vorsprungautowerk.com · ✅ Free US shipping on orders over $425
Supercharged 3.0T owner? The pump-only listing has no harness, so order the CWA-100 pump and harness kit to plug straight into your factory connector.
What Is in Our Kit and Why
The genuine Pierburg CWA-100-3 is the brand-name part. The Vorsprung VWA-100 is our in-house equivalent, engineered and flow-tested to match it at a lower price, with the same flow, voltage and control specs and the same fit. Pick genuine if the badge matters, or the VWA-100 if only the performance does.
- ✅ Either pump: brushless, PWM-controlled, sealed to IP6K9K and IPX7, with 20 mm hose connections.
- ✅ Adapter harness (kit only): factory CWA-50 connector to the CWA-100 plug, with no cutting or splicing.
- ✅ Factory mounting and control: standard Pierburg cushion clamps, the factory location and the factory PWM signal, with no tune.
Pump only: $179.99 (VWA-100) or $299.99 (Pierburg) on the pump-only listing. Pump and harness: $199.99 or $309.99 in the 3.0T kit.
Build the Rest of the Loop
On Gen 1 engines, the Sehr Gut divorced supercharger cooling port kit ($67.67) swaps the small factory intercooler ports for four larger adapters with new OE gaskets. It does not fit CREC engines.
Our GP Ice heat exchanger v2 ($449.99) is still being tested with CWA-100 and CWA-150 pump setups, per its listing, so check availability first. Hoses and billet fittings live in our Audi cooling upgrades collection.
Fitment: Which Audi 3.0T Cars Take the CWA-100 Kit
Per its listing, the CWA-100 pump and harness kit fits Audi 3.0T supercharged (EA837) cars that use the factory CWA-50 pump connector: the B8 and B8.5 S4 and 3.0T S5, the Q5 3.0T and SQ5, the C7 A6 and A7, the D4 A8, and the 4L and 4M Q7. That covers Gen 1 engines and the CREC engines in the 2016 to 2018 A6 and A7, the 2015 to 2018 A8 and the 4M Q7.
Some kits on the market use a different harness for CREC cars, so confirm your connector or email your VIN to help@vorsprungautowerk.com first. The pump-only listing is a direct replacement for Audi part 4N0965567, which the listing cross-references to later models such as the A7 Sportback, A8 and Q5 plug-in hybrid; on an EA837 it needs the kit's harness. Driving a 4.0T, a B9 or a C6 A6? Email your VIN before ordering.
Install Notes: Swap It, Bleed It, Log It
Tools: metric hand tools, hose clamp pliers, two hose pinch clamps, a drain pan, the right coolant for your car plus distilled water (see our G13 coolant guide), and a scan tool that runs Audi output tests. Time depends mostly on access on your chassis and your patience with bleeding.
- Find the pump. In Audi's guide (C6 A6) it sits at the front left, next to the oil cooler. On a B8.5 S4, owners describe reaching it from the driver's side through the fog light grille, the underbody panel or the wheel well liner.
- Work cold. Pinch the hoses on both sides of the pump and unplug it.
- Swap it. Owners report the CWA-50 and CWA-100 housings fit the same bracket. The CWA-100-3's barbs are a touch shorter, so push the hoses fully home.
- Connect the harness and route it away from heat and sharp edges.
- Check the fuse. The CWA-100 is rated to draw more current, and fuse layouts vary by chassis and year. Confirm the fuse is healthy and correct, and never upsize it past what the wiring is built for.
- Fill first. Top up the expansion tank before the pump ever runs.
- Bleed it. Run the pump with a scan tool output test and open the intercooler bleed screws one at a time until coolant flows without bubbles, topping up as you go. Audi's service information has the official procedure.
- Recheck and log. Owners report small air pockets working out over a few days, so check the level cold after a few drives, then log intake temperatures.
Audi CWA-100 Coolant Pump Upgrade FAQ
What does a CWA-100 coolant pump upgrade do on an Audi 3.0T?
It replaces the factory CWA-50 intercooler pump with one rated for more pressure and flow, so coolant keeps moving between the intercoolers and the front radiator even in a restrictive loop. That helps the car recover between pulls.
Can I just run the factory CWA-50 at full speed instead?
Some owners cut its PWM wire so it runs flat out. That only reaches the CWA-50's own ceiling of up to 24 L/min and 0.6 bar, and it takes the pump away from the ECU.
Do I need a tune for the CWA-100 upgrade?
No. Per our listings, both the Pierburg CWA-100-3 and the Vorsprung VWA-100 accept the factory ECU's standard PWM signal. Tuned cars make more heat, so they have the most to gain.
Does the CWA-100 kit fit CREC engines?
The listing covers EA837 cars with the factory CWA-50 connector, including the 2016 to 2018 A6 and A7 and the 4M Q7. Some kits use a different CREC harness, so confirm your connector or send us your VIN.
Should I upgrade the pump or the heat exchanger first?
Ideally both, because each limits the other. A CWA-100 on a stock core mostly speeds up recovery, and a bigger core without more flow leaves volume unused. Doing both? Do them together and bleed once.
How do I bleed the intercooler loop after the swap?
Fill the expansion tank before the pump runs, run it with a scan tool output test, open the intercooler bleed screws one at a time until coolant flows without bubbles, and recheck the level cold after a few drives.
What is the difference between the Pierburg CWA-100 and the Vorsprung VWA-100?
The Pierburg CWA-100-3 is the brand-name part. The Vorsprung VWA-100 is our in-house equivalent, engineered and flow-tested to the same specs at a lower price, with the same mounting and harness.
Bottom Line on the CWA-100 Upgrade
Heat soak on a supercharged 3.0T is no mystery: the loop gets hot, the ECU protects the engine, and the factory CWA-50 can only push so hard. The Audi CWA-100 coolant pump upgrade raises that ceiling, keeps factory control and skips the Audi Tax. Order the pump alone or, for an EA837, the pump and harness kit, then bleed it like you mean it.
Shop the 3.0T Pump and Harness Kit, from $199.99
Drive the difference. Drive Vorsprung.
Prices checked October 26, 2026 and subject to change.

