Your 3.0T's PCV valve has a talent for failing in the worst possible spot: the back of the engine valley, right under the supercharger. Every replacement means pulling the blower and paying the Audi Tax on labor. An Audi 3.0T PCV relocation changes where the next failure happens. A billet adapter takes over the failure-prone section of the factory housing, and the pressure-regulating valve moves out to where you can reach it, paired with our 06E103772C PCV relocation oil separator. Is it the right call for your car, or is a new OE valve smarter? Here is the honest version, cons included.
Why the Factory 3.0T PCV Valve Wears Out Its Welcome
On the EA837 3.0T, the PCV valve is an oil separator with a rubber pressure-regulating diaphragm, bolted into the back of the valley under the supercharger. Heat and age harden that diaphragm and the plastic around it. Once it stops regulating, the engine either pulls in unmetered air or the crankcase builds pressure.
- ✅ A whistle or squeal from the back of the engine, loudest at idle
- ✅ A rough or hunting idle
- ✅ Lean codes, or the PCV regulator code P052E
- ✅ Strong suction on the oil filler cap with the engine running
- ✅ Rising oil consumption
The part is not the expensive bit. Getting to it is. Shops commonly quote $600 to $900 for a B8 or B8.5 S4 PCV job, with 3 to 5 hours of labor, because the supercharger has to come off. Owners report an $815 dealer quote on an SQ5, a valve that failed at 39,116 miles and a 2016 A6 with PCV replacements at 65,000 and 86,000 miles. Not sure it is the valve? Our Audi PCV valve diagnosis guide walks through the tests.
What an Audi 3.0T PCV Relocation Actually Does
A relocation keeps the factory PCV housing in the valley but replaces its failure-prone lower section with a billet aluminum adapter. That adapter has 12AN ORB ports, so AN lines can carry the crankcase gases out from under the supercharger to a separate oil separator and pressure-regulating valve mounted where you can reach them. The cleaned gases still go back into the intake, just like the factory system.
In our lineup, that remote hardware is the 06E103772C oil separator, a baffled separator with no diaphragm of its own, and the 06E103245E crankcase vent valve, which does the pressure regulating. Both are OE cross-referenced parts from Audi's 3.2 FSI V6, so a future replacement valve is a $19.99 part, not a supercharger-off weekend.
PCV Relocation vs OE Replacement: The Honest Pros and Cons
Relocation is not automatically better. It trades one hassle for another.
Why owners relocate
- ✅ The next vent valve or diaphragm swap happens with the supercharger left in place.
- ✅ Billet aluminum replaces the plastic section that tends to get brittle and crack in the valley heat.
- ✅ The lines and remote valve sit in the open, easy to check and replace.
- ✅ Running costs stay low: the vent valve is $19.99 and an upgraded Viton GLT diaphragm is $19.99.
Why some owners stick with OE
- The first install still means pulling the supercharger, same as a factory PCV job.
- It is a custom build: you supply the fittings and hose, and every extra joint is one more seal to get right.
- The thermostat, injector seals and intercoolers still live under the supercharger, as skeptical owners point out on the forums.
- The relocated valve comes from a different engine, and owners report that even switching factory PCV revisions can call for a software update.
- Opinions are split. One owner's shop reported problems with a relocation kit, and information for CREC engines is thin.
Our take? For a stock daily driver you will not keep for years, the correct OE valve, replaced with the rest of the valley parts in one visit, is usually smarter (see our 3.0T PCV valve replacement guide). Keeping the car long term, wrenching yourself or running a tune? Relocation earns its keep.
What to Look For in a 3.0T PCV Relocation
- ✅ No permanent surgery: a bolt-on adapter with no adhesive, cutting or permanent modification.
- ✅ Real oil separation in the remote circuit, not just a valve on a hose.
- ✅ Cheap wear parts: a regulating valve and diaphragm you can buy again for about $20 each.
- ✅ Proper ports: 12AN ORB threads, so you pick the hose size and routing, catch can included.
- ✅ A mounting plan for your chassis, not zip ties on a hot hose.
- ✅ A closed system that still returns blow-by to the intake.
- ✅ Fitment confirmed by VIN, especially on CREC engines.
Vorsprung Relocation Parts vs Name-Brand Kits vs a Dealer PCV Job
Our three core relocation parts, the billet adapter ($74.99), the 06E103772C separator ($199.99) and the 06E103245E vent valve ($19.99), total $294.97. The name-brand relocation kit we priced runs about $275, was sold out when we checked and leaves the hoses and fittings to you, and its billet adapter alone is about $126. A factory fix means a new PCV back under the supercharger: the genuine 06E103547AH lists at $331.64, and shops commonly quote $600 to $900 for the job.
| Vorsprung relocation parts | Name-brand relocation kit | Dealer or factory PCV replacement | |
|---|---|---|---|
| What you get | Billet adapter with battery-location mount, 06E103772C separator, 06E103245E vent valve | Billet adapter plus throttle body spacer hardware | New plastic PCV assembly in the stock location |
| Parts price | $294.97 for the three core parts | About $275 | About $332 list for 06E103547AH |
| Billet adapter alone | $74.99 | About $126 | Not applicable |
| Where the regulating valve lives | Out from under the supercharger | Out from under the supercharger | Under the supercharger |
| Next valve service | Supercharger stays on | Supercharger stays on | Supercharger off again |
| Hoses and fittings | You supply 12AN ORB fittings and AN hose | You build the hoses | None needed |
| First install | Supercharger off once, plus plumbing | Supercharger off once, plus plumbing | Shops commonly quote 3 to 5 hours, every time |
Ready to build it? Start with the 06E103772C oil separator for your 3.0T PCV relocation, then add the adapter and vent valve below.
Shop the 06E103772C Relocation Separator, $199.99
✅ Audi OE part numbers and Hengst OE-supplier PCV valves · ✅ Fitment help by VIN at help@vorsprungautowerk.com · ✅ Free US shipping on orders over $425
What's in a Vorsprung 3.0T PCV Relocation and Why
- ✅ Billet PCV housing adapter ($74.99): machined aluminum in place of the vulnerable lower section of the factory plastic housing, with 12AN ORB ports. It includes a billet battery-location mount (confirmed for B8 and B8.5 S4 and S5), and needs no adhesive, cutting or permanent modification to the original housing.
- ✅ PCV relocation oil separator, 06E103772C ($199.99): a baffled separator that pulls oil out of the blow-by before it heads back to the intake. It supersedes 06E103464D and is a direct OEM fit on the A4 and A6 3.2 FSI V6. It is on pre-order and shipping in batches, so check the listing for timing.
- ✅ Crankcase vent valve, 06E103245E ($19.99): the pressure-regulating valve, diaphragm inside, that most relocation builds are designed around.
- ✅ GLT TruSeal PCV diaphragm upgrade ($19.99): a Viton GLT diaphragm molded from the original OEM part, rated from -40°F to +400°F, for the relocated valve.
- ✅ Optional: the 06E103217M breather hose ($49.99) for relocation and catch-can routing, and the billet 19mm to 10AN valve cover quick connect.
You supply the 12AN ORB adapter fittings and AN hose. Unsure about routing? Email help@vorsprungautowerk.com with your VIN first.
Fitment: Which 3.0T Cars Can Relocate
Every core part in our relocation lists the 2010 to 2016 B8 and B8.5 S4, the B8 and B8.5 S5 (on 2010 to 2012 cars that means the S5 Cabriolet, since the coupe had the 4.2 V8) and the C7 A6 3.0T. The billet PCV housing adapter also lists the 2013 to 2017 Q5 3.0T and the 2014 to 2017 SQ5, but its battery-location mount is confirmed for the S4 and S5 only, so Q5, SQ5 and A6 owners should plan their own mounting spot and email us first.
The separator and vent valve listings also name the A7, A8 and Q7, but the adapter listing does not, and CREC engines (2016 and later A6 and A7, 2015 and later A8, 2017 to 2019 Q7) use a different factory PCV, 06E103547AF. Drive one of those? Send your VIN to help@vorsprungautowerk.com first, or check your engine with our Gen 1 vs CREC engine guide.
Sticking with OE? The Hengst 06E103547AC fits the B8 S4, S5 and C6 A6, the 06E103547AH fits the B8.5 S4, S5, Q5 and SQ5, and the 06E103547AF fits CREC engines. Doing the whole valley? The B8.5 under supercharger kit bundles the PCV with the thermostat housing, water pump and gaskets.
Install Notes: Time, Tools and Tips
- ✅ Budget it like a PCV job. The supercharger comes off for the first install. Shops commonly quote 3 to 5 hours for a factory PCV replacement, and a published DIY guide says to set aside a full day. Add time for mounting and plumbing.
- ✅ Do the valley while it is open. If your thermostat housing, water pump, injector seals and intake gaskets are original, this is the cheap time to replace them.
- ✅ Tools: 8 to 27mm sockets, T20, T25 and T30 Torx, a 5mm hex bit, a torque wrench, picks, a drain pan, a fluid extractor and AN wrenches.
- ✅ Keep it clean: rag the open ports, label vacuum lines, start bolts by hand and use new supercharger gaskets.
- ✅ Route lines with care, clear of the belt drive and hot exhaust parts, and secure them against chafing.
- ✅ Verify the work: smoke test for leaks, clear codes and log idle fuel trims over a few drives. Chasing a hose instead? See our 3.0T PCV breather hose guide.
Audi 3.0T PCV Relocation FAQ
What is an Audi 3.0T PCV relocation?
A billet adapter replaces the lower section of the factory PCV housing, and AN lines carry blow-by to a separator and vent valve mounted within reach. The gases still return to the intake.
Is a PCV relocation better than a new OE PCV valve?
Not for everyone. An OE valve keeps the car factory-correct with no custom plumbing. A relocation means the next valve swap skips the supercharger removal, which suits long-term owners, DIYers and tuned cars.
Do I still have to remove the supercharger for a PCV relocation?
Yes, once. The factory PCV housing sits under the supercharger, so the first install is a supercharger-off job. After that, the vent valve is serviced with the supercharger in place.
What parts do I need for a 3.0T PCV relocation?
The billet PCV housing adapter ($74.99), the 06E103772C oil separator ($199.99) and the 06E103245E vent valve ($19.99), plus 12AN ORB adapter fittings and AN hose. The GLT TruSeal diaphragm ($19.99) is a worthwhile add.
Does a PCV relocation need a tune?
None of our relocation listings call for one, but owners report that even switching factory PCV revisions can call for a software update, so check with your tuner and log fuel trims.
Will a PCV relocation fit my CREC A6, A7, A8 or Q7?
CREC engines use a different factory PCV, 06E103547AF, and relocation information for CREC cars is thin. Email help@vorsprungautowerk.com with your VIN before you order.
Does a PCV relocation vent the crankcase to the air?
No. A proper relocation keeps the system closed and returns blow-by to the intake, like the factory system. Never vent the crankcase to the atmosphere, and check your local inspection rules before modifying emissions-related parts.
How much does a 3.0T PCV relocation cost?
Our three core parts total $294.97 before fittings and hose. Expect first-install labor similar to a factory PCV job, which shops commonly quote at 3 to 5 hours, plus plumbing time.
Bottom Line on the Audi 3.0T PCV Relocation
Want the whistle gone and the car factory-correct? Buy the right OE valve and do the valley in one visit. Tired of pulling a supercharger for a rubber diaphragm? An Audi 3.0T PCV relocation moves the part that fails to where you can reach it. Start with the 06E103772C PCV relocation oil separator, add the billet adapter and vent valve, and browse our OEM+ upgrades and fixes while you plan the build.
Start Your Relocation: 06E103772C Separator, $199.99
Drive the difference. Drive Vorsprung.
Prices checked October 30, 2026 and subject to change. Labor figures are typical shop quotes or owner reports.

