Shopping for Audi 3.0T headers? The supercharged V6 likes a freer-breathing exhaust side, but on this engine the headers are the easy part and getting them in is the job. This guide covers what long-tube and shorty designs replace, the build details that separate a set you install once from a set that cracks, what comes out of the car, and what each listing says about tuning. It's built around our HEH Headers V2 for the supercharged Audi 3.0T, and it applies to any header you're cross-shopping for the S4, S5, Q5, SQ5, A6, A7 or A8.
For off-road and competition use. Check your local emissions and inspection rules before modifying your exhaust.
Why the Factory Manifolds Become the Bottleneck
The supercharger crams air in from the valley of the engine, and all of it leaves through the factory manifolds, one per bank, straight into the front pipes that hold the factory front catalytic converters. At stock power, that layout does its job. Once a car is pulleyed, ported and tuned, many owners look at the exhaust side next. So when do headers make sense?
- ✅ Your build already moves more air. Owners generally expect headers to matter most on pulleyed, ported or tuned cars.
- ✅ The front pipes are coming out anyway. The factory cats bolt straight to the manifolds, so a cat or test pipe job shares much of the teardown.
- ✅ You only want to pay for this labor once. That makes build quality matter more than usual.
Long-Tube vs Shorty Headers on the 3.0T: What Each One Replaces
This decision drives everything else, and it's really about where the header ends.
- ✅ Shorty headers replace only the manifold and bolt to a front pipe below them, so that section stays your call. The listing for our Vorsprung Shorty Headers for the 3.0T says to pair them with a matched front pipe, such as our catless test pipes or high flow cats.
- ✅ Longer designs, often sold as long-tube headers, take over the front pipe section too. That's how our HEH Headers V2 listing describes them: they replace the manifold and the test pipe section and work with OEM or aftermarket downpipes.
Why does it matter? The front pipe section is where the factory front cats live. A header that replaces it changes your emissions equipment and your parts list, since it takes the spot test pipes or high flow cats would otherwise fill. Decide that before you buy, and check your local inspection rules first.
What to Look For in Audi 3.0T Headers
These headers live in a hot, cramped spot next to the subframe, the engine mounts and the steering shaft. Check these before you buy:
- ✅ Where it ends. Manifold only, or the test pipe section too? That decides your catalyst plan and your parts list.
- ✅ Equal-length primaries. Same-length runners mean each exhaust pulse travels the same distance to the collector, which helps scavenging and keeps every cylinder on a bank breathing alike.
- ✅ The right stainless. 321 is essentially 304 with titanium added for stabilization. That prevents the chromium carbide formation that can leave unstabilized stainless prone to intergranular corrosion between roughly 800 and 1,500°F, which is why 321 is used for aircraft exhaust stacks and manifolds. Plenty of 3.0T sets use 304.
- ✅ Wall thickness and flanges you can verify. Thicker tube resists cracking and rings less, yet many listings never state wall thickness. Look for CNC-machined, reinforced flanges that sit flat on the head.
- ✅ Back-purged TIG welds. Argon on the inside of each joint keeps the weld root clean instead of oxidized, and oxidized roots are where cracks like to start.
- ✅ Real heat management. Insulation under a formed metal shield, not foil wrapped around a pipe and called shielding.
- ✅ Hardware in the box and a seller who will check your VIN.
A clean, back-purged TIG weld on one of our V2 test pipe flanges:
Audi 3.0T Headers Compared: HEH V2 vs Name-Brand Sets vs Factory Manifolds
Our HEH Headers V2 are an equal-length, 321L stainless design, TIG welded and back purged, that replaces the manifold and the test pipe section, with all hardware included: $1,599.99 with Standard Heat Shielding or $1,999.99 with Dual Layer. The US-listed name-brand 3.0T sets we checked run about $850 to $2,000, 304 stainless is common, wall thickness often goes unpublished, and heat shielding ranges from not mentioned to included.
| Vorsprung HEH Headers V2 | Typical name-brand 3.0T headers | Factory manifolds | |
|---|---|---|---|
| Price | $1,599.99 Standard, $1,999.99 Dual Layer | About $850 to $2,000 (US sets we checked) | Already on the car |
| What it replaces | Manifold and test pipe section, per the listing | Manifold only, or manifold plus the catted front pipe | Nothing; feeds the catted front pipe |
| Material and welds | 321L stainless, TIG welded and back purged | 304 is common; wall thickness often unpublished | Production part |
| Heat management | Standard shielding, or dual quartz wool plus a metal shield | From none mentioned to coating plus shielding | Factory setup |
| Hardware | All included, bolt-on | Varies; check the box | Not applicable |
| Intended use | Off-road and competition only | Commonly off-road or racing only | Original equipment |
Want one part that covers the manifold and the front pipe section, with real shielding and every nut in the box? That's the HEH Headers V2 for the supercharged 3.0T.
Shop the HEH Headers V2, $1,599.99 to $1,999.99
✅ 321L stainless, TIG welded and back purged · ✅ Fitment help by VIN at help@vorsprungautowerk.com · ✅ Free US shipping on orders over $425
What You Get With the HEH Headers V2
- ✅ Equal-length primaries with smooth, flow-optimised transitions.
- ✅ 321L stainless, 100% TIG welded and back purged, with reinforced inner welds and CNC-machined 321L flanges to OEM specs.
- ✅ Two shielding options: Standard Heat Shielding, or Dual Layer with dual quartz wool insulation and a metal heat shield, aimed at lower under-hood temperatures.
- ✅ Bolt-on with all hardware included, compatible with OEM or aftermarket downpipes, and 100% handcrafted.
Stock can differ between the two shielding options, so check the listing when you order.
Our Other 3.0T Header Options
- ✅ Vorsprung Shorty Headers, $999.99. Mandrel-formed stainless at 2.0mm wall, TIG welded and back purged, with a CNC-machined head flange, a real silver ceramic coating and reinforced slip-fit flanges. Listed as a pre-order for Winter '26 delivery.
- ✅ The limited-run "Not Vorsprung Autowerk" 3.0T headers, $549.99. Per the listing, a small manufacturing oopsie produced a run of nine, ever, with no restock. They fit the same cars as the HEH V2, ship bare as a blank canvas and are sold as-is. "Not our headers," the listing insists. We respect that.
- ✅ Not ready for headers? Our Audi S4 Test Pipes V2, $449.99, replace just the factory front cats, with dual-layer heat shielding, gaskets and hardware included. Off-road and competition use only.
Browse the B8 and B8.5 S4 and S5 exhaust collection for high flow cats and the rest of the system.
Audi 3.0T Headers Fitment
Per its listing, the HEH Headers V2 fit the supercharged 3.0T V6 (EA837) in the B8 and B8.5 S4 (2010 to 2016), S5 (2010 to 2017, with 2010 to 2012 being the Cabriolet only), Q5 (2013 to 2017) and SQ5 (2014 to 2017), the C7 and C7.5 A6 (2011 to 2017) and A7 (2010 to 2017), and the D4 A8 (2011 to 2017). The limited-run headers list the same coverage, while the Shorty Headers listing runs its A6, A7 and A8 ranges through 2019.
Model-year labels for the C7 and D4 cars vary by market, so if your car sits at either end of a range, email your VIN to help@vorsprungautowerk.com first. The B9 S4 and S5 use the turbocharged EA839, and the Q7 isn't on these listings.
Installing Audi 3.0T Headers: Time, Tools and Tips
The manifolds sit low on the outside of each bank, and the factory cats bolt straight to them. That's where the real Audi Tax lives: not in the parts, in the packaging.
- ✅ What comes out: owners describe two routes. In the car, the engine is supported from above, both engine mounts come out, the transmission mount and crossmember are lowered, and the steering shaft is disconnected for room. Or drop the subframe or the whole powertrain, which some owners find faster.
- ✅ Time: one B8 S4 owner reported roughly 10 to 11 hours of shop labor. Owners say S tronic cars have less room than six-speeds, and some shops pull the engine on those. Get a written quote.
- ✅ Tools: a lift, an engine support bar, swivels and long extensions, an O2 sensor socket, penetrating oil, a stud extractor and a torque wrench with the factory specs.
- ✅ Tips: soak the studs the day before, paint-mark the steering shaft, use new gaskets and nuts, test-fit both banks, and recheck after a few heat cycles.
Our step-by-step guide on how to install headers on an Audi 3.0T has the full walkthrough, and the Audi S4 test pipes install guide covers getting the factory cats out.
Tuning, Check Engine Lights and the Rules
Tune requirements differ by listing. The HEH V2 listing says headers alone don't require a dedicated tune and recommends one when you add a ported supercharger, a pulley or downstream exhaust changes. The Shorty Headers listing says to plan on a properly tuned ECU calibration. The limited-run listing doesn't state a requirement, so ask us or your tuner.
After exhaust work, changing or removing catalytic converters is what commonly sets codes such as P0420 and P0430. Our test pipes vs high flow cats comparison and our guide to high flow catalytic converter legality cover the rest.
For off-road and competition use. Check your local emissions and inspection rules before modifying your exhaust.
Audi 3.0T Headers FAQ
Are headers worth it on a supercharged Audi 3.0T?
They make the most sense on a car that's already pulleyed, ported or tuned, or when the front pipes are coming out anyway. Owners are split on how much they add over test pipes alone, so treat them as a step for a built car.
Should I buy long-tube or shorty headers for my S4?
Pick a shorty if you want to keep choosing what goes in the front pipe section. Pick a longer design like the HEH V2 if you want one part that replaces both the manifold and the test pipe section, per its listing.
Do Audi 3.0T headers replace the catalytic converters?
It depends on the design. The factory front cats sit in the front pipes right off the manifolds. A shorty bolts ahead of them, while the HEH V2 listing says it replaces the manifold and the test pipe section.
Do I need a tune after installing 3.0T headers?
Per the HEH V2 listing, headers alone don't need a dedicated tune, but one is recommended with a ported supercharger, a pulley or other exhaust changes. The Shorty Headers listing calls for a properly tuned ECU calibration.
How long does a 3.0T header install take?
Plan on a big job. One B8 S4 owner reported roughly 10 to 11 hours of shop labor, and owners say S tronic cars have less room than manuals. Get a written quote first.
Do these headers fit the B9 S4 or the Q7?
No. Our header listings cover the supercharged B8 and B8.5 S4, S5, Q5 and SQ5, the C7 and C7.5 A6 and A7, and the D4 A8. The B9 uses the turbocharged EA839, and the Q7 isn't on these listings.
Can I run 3.0T headers on the street?
Our headers are sold for off-road and competition use only and are not designed to meet emissions standards. Check your local emissions and inspection rules before you modify your exhaust.
Bottom Line on Audi 3.0T Headers
Pick the design first, because where your headers end decides everything downstream. Then buy on build quality: equal-length runners, 321 stainless, back-purged welds, real shielding and hardware in the box, because nobody wants to pay for this labor twice. That's exactly why we built the Audi 3.0T HEH Headers V2.
Shop the HEH Headers V2, $1,599.99 to $1,999.99
Drive the difference. Drive Vorsprung.
Prices checked October 31, 2026 and subject to change. Labor figures are owner-reported and vary by shop.


