Your Audi 3.0T needs a thermostat, the PCV valve is whistling, or a shop just told you the supercharger has to come off. Sound familiar? The smart move is an Audi 3.0T under supercharger kit: every wear part that lives under the blower, in one box, so you pay for supercharger removal once instead of twice. The catch is that Audi changed the parts by chassis, build date and engine generation, and the PCV valve alone comes in four part numbers. This guide matches your car to the right kit in about two minutes. Driving a B8.5 S4, S5, Q5 or SQ5? Your match is our B8.5 under supercharger kit for the S4, S5, Q5 and SQ5.
Why the Supercharger Has to Come Off (and Why Once Is Enough)
On the supercharged 3.0T, the blower sits in the valley of the V6, right on top of the thermostat housing and the PCV valve, so either repair starts with supercharger removal. Owners report shops quoting about 4 to 5 hours of labor for a thermostat or PCV job. One 2013 S5 owner posted a dealer estimate near $2,000, with 9.5 hours of labor, for a thermostat, water pump and crossover pipe, and typical estimates for a 2013 S4 thermostat alone run roughly $1,000 to $1,400. That is the Audi Tax at its finest: a plastic part worth a sliver of the invoice, buried under hours of labor.
Signs that something under the supercharger is on its way out:
- ✅ Coolant loss with no obvious drip, or a sweet coolant smell after a drive
- ✅ A low coolant or overheating warning on the dash
- ✅ A whistle or rough idle from a tired PCV valve diaphragm
- ✅ A check engine light for crankcase ventilation or thermostat performance
Still hunting the leak? Start with our Audi 3.0T coolant leak guide, and see the 3.0T PCV valve replacement guide for the PCV side.
Which Under Supercharger Kit Fits My Car?
Here is the short version: five kits, split by PCV valve. The 2010 to 2012 B8 S4 and S5 Cabriolet and the 2009 to 2011 C6 A6 take 06E103547AC and the B8 and C6 under supercharger kit. B8.5 S4, S5, Q5 and SQ5 owners, plus the 2013 to 2014 A8, take 06E103547AH. C7 A6 and A7 built from May 2012 through 2015 and the 2011 to 2015 4L Q7 take 06E103547AK and the C7 A6, A7 and 4L Q7 kit, while 2012 cars built before May stay on 06E103547AC with the early 2012 C7 kit. Every CREC car takes 06E103547AF and the Gen 2 CREC under supercharger kit.
| Your car | Model years | Engine | PCV valve | Your kit |
|---|---|---|---|---|
| B8 S4 | 2010-2012 | Gen 1 | 06E103547AC | B8 and C6 kit, from $574.99 |
| B8 S5 Cabriolet | 2010-2012 | Gen 1 | 06E103547AC | B8 and C6 kit, from $574.99 |
| C6 A6 3.0T | 2009-2011 | Gen 1 | 06E103547AC | B8 and C6 kit, from $574.99 |
| C7 A6 and A7 built before 05/2012 | 2012 | Gen 1 | 06E103547AC | Early 2012 C7 kit, from $674.99 |
| B8.5 S4 | 2013-2016 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| B8.5 S5 coupe and Cabriolet | 2013-2017 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| Q5 3.0T (8R) | 2013-2017 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| SQ5 (8R) | 2014-2017 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| D4 A8 3.0T | 2013-2014 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| VW Touareg, supercharged 3.0T | 2011-2016 | Gen 1 | 06E103547AH | B8.5 kit, from $649.99 |
| C7 A6 and A7 built 05/2012 or later | 2012-2015 | Gen 1 | 06E103547AK | C7 and 4L Q7 kit, from $639.99 |
| 4L Q7 3.0T | 2011-2015 | Gen 1 | 06E103547AK | C7 and 4L Q7 kit, from $639.99 |
| C7.5 A6 and A7 | 2016-2018 | CREC | 06E103547AF | Gen 2 CREC kit, from $649.99 |
| D4 A8 3.0T | 2015-2018 | CREC | 06E103547AF | Gen 2 CREC kit, from $649.99 |
| 4M Q7 3.0T | 2017-2019 | CREC | 06E103547AF | Gen 2 CREC kit, from $649.99 |
On the line between two rows? Check the build month on your driver's door jamb sticker and email your VIN to help@vorsprungautowerk.com before you order. (The 2010 to 2012 S5 coupe has the 4.2 V8, not the 3.0T.) Driving a B8.5? The B8.5 Audi 3.0T under supercharger kit is your box.
Shop the B8.5 Under Supercharger Kit, $649.99
✅ Graf, Hengst, Elring and Rein OE-supplier parts · ✅ Fitment help by VIN at help@vorsprungautowerk.com · ✅ Free US shipping on orders over $425
How to Confirm Your Engine and Build Date
Model year gets you most of the way, but Audi did not change parts on January 1. Three quick checks settle it:
- ✅ Engine generation: in our kit listings, the 2016 to 2018 A6 and A7, 2015 to 2018 A8 and 2017 to 2019 Q7 are CREC. Earlier supercharged 3.0T cars are Gen 1 EA837.
- ✅ Engine code: it is on the vehicle data label, which the 2015 A8 owner's manual, for one, places in the spare wheel well.
- ✅ Build month: it is on the driver's door jamb sticker, and it only matters for 2012 A6 and A7, where May 2012 splits 06E103547AC from 06E103547AK.
More on both engines in our Audi 3.0T supercharged engine guide.
What Every Under Supercharger Kit Contains, and Why
All five kits share the same backbone: the parts that fail under the blower, plus the seals you disturb getting it off and back on.
- ✅ Billet aluminum thermostat housing and thermostat as one assembly, replacing the factory plastic housing that tends to crack (06E121111AL on Gen 1, 06E121111AT on CREC). More in our billet thermostat housing breakdown.
- ✅ Graf metal water pump. It shares the drain, belts and refill with the thermostat job, so it rides along for less labor than a separate visit.
- ✅ The OE PCV valve your car is cataloged for: Hengst 06E103547AC, AH or AF, or Rein 06E103547AK.
- ✅ Elring upper and lower intake manifold gaskets, six of each, so nothing gets reused.
- ✅ Genuine VW/Audi PCV-to-supercharger adapter pipe (06E103213).
- ✅ Elring injector seals for all six injectors (06E998907E on Gen 1, 06E998907F on CREC). Our 3.0T injector seals guide explains when they matter.
Wondering how our kit compares to the best-known name-brand kit? We broke that down part by part in a separate post.
What Changes From Kit to Kit
- ✅ PCV valve: AC in the B8 and C6 kit and the early 2012 C7 kit, AH in the B8.5 kit, AK in the C7 and 4L Q7 kit, AF in the CREC kit.
- ✅ Water pump: the B8 and C6 kit replaces 06E121018A, the other Gen 1 kits 06E121018N, and the CREC kit uses the Graf PA1228.
- ✅ Heater pipe: every Gen 1 kit adds an aluminum heater pipe in place of the plastic 06E121065N. CREC engines do not use that pipe.
- ✅ Breather hose: the B8 and C6 and early 2012 C7 kits add the genuine 06E103207P breather hose and clamp.
- ✅ CREC seals: 06E129717F lower intake gaskets and 06E998907F injector seals.
Every Gen 1 kit also offers three add-ons: GLT TruSeal intake gaskets (+$25), a 06A919501A coolant temperature sensor (+$20) and coolant (+$25). The CREC kit offers coolant.
What to Look For in Any Under Supercharger Kit
Shopping around? Whoever you buy from, hold the kit to this checklist:
- ✅ The PCV valve by exact part number, not "fits all Gen 1." The wrong valve is a fun surprise with the supercharger sitting on your fender.
- ✅ A thermostat housing that is not the same plastic that just failed, with the thermostat included.
- ✅ Fresh intake manifold gaskets for every joint you open.
- ✅ Part numbers printed on the listing, so you can cross-check against your VIN.
- ✅ OE-supplier hard parts from names like Graf, Hengst and Elring rather than unbranded copies.
What Else to Do While the Supercharger Is Off
The blower is off, the coolant is out and the valley is wide open. It is also step one on our Audi 3.0T upgrade path. Knock out the neighbors now:
- ✅ Timing chain oil check valves. Our 3.0T oil check valve set ($109.99, two German-made valves) lives in the engine valley and targets the cold-start rattle. It is listed for the 3.0T S4, S5, SQ5, A6, A7 and Q7 from 2009 to 2017, so email your VIN for anything else. More in our timing chain rattle guide.
- ✅ Supercharger tensioner pulley. The belt is already off and the factory pulley is plastic. Our billet supercharger tensioner pulley is $64.99 alone or $111.99 with an OEM tensioner.
- ✅ PCV-to-intake pipe. Our B8.5 and C7 listings flag it as a common companion failure (06E103207AC on most of those cars, 06E103207P on early-production 2013 S4 and S5).
- ✅ CREC coolant crossover pipes. On CREC engines, the plastic crossover pipes between the water pump and thermostat housing share the same hot valley. Find the crossover kit, PCV pipes and more in our under supercharger kits collection.
- ✅ Gasket upgrade. The GLT TruSeal intake manifold gasket set is $49.99 on its own, or a $25 add-on to any Gen 1 kit.
Install Notes: Time, Tools and Tips
This is a big job, not a driveway oil change. One owner reported about 4 hours for a 2012 C7 A6 water pump, thermostat and supercharger gaskets, and a detailed write-up logged 8 hours with two people the first time. One mechanic estimated a water pump adds about 1.5 hours when it rides along with a thermostat job, versus about 2.2 hours on its own. Our 3.0T water pump replacement guide covers the pump side.
- ✅ Label everything: mark every vacuum hose and connector with a paint pen first.
- ✅ Expect hidden steps: owners have been caught out by the water pump pulley, vacuum pump and air box, and one C7 owner needed a helper to pull the radiator forward for clearance.
- ✅ Tools: a full Torx set, a flat breaker bar, a pulley pin wrench and plugs for the open intake ports.
- ✅ Seal it right: clean every sealing surface, lube coolant O-rings with coolant, not grease, and keep oil off hose connections.
- ✅ Bleed and recheck: fill to the MAX mark cold, follow the factory bleed procedure and recheck the level after a few drives.
Audi 3.0T Under Supercharger Kit FAQ
What is an Audi 3.0T under supercharger kit?
The parts that live under the supercharger, or get disturbed removing it, in one box: thermostat housing and thermostat, water pump, PCV valve, intake manifold gaskets, PCV adapter pipe and injector seals, plus a heater pipe on Gen 1 engines. You pay for supercharger removal once.
Which under supercharger kit do I need?
Your PCV valve decides it: AC for B8, C6 and early 2012 C7 cars, AH for B8.5 cars and the 2013 to 2014 A8, AK for later C7 A6 and A7 and the 4L Q7, and AF for CREC cars. The table above maps every car to its kit.
Do I have to remove the supercharger to replace the thermostat on an Audi 3.0T?
Yes. The thermostat housing and PCV valve both sit under the supercharger, which is why owners replace the rest of the valley parts in the same visit.
How much does it cost to install an under supercharger kit?
Labor is the big number. Owners report shops quoting about 4 to 5 hours for a thermostat or PCV job, and one owner's dealer estimate came close to $2,000 with a water pump and crossover pipe added. Get a written quote.
Which kit fits a 2012 Audi A6 or A7?
Check the build month on the driver's door jamb sticker. Built before May 2012: the early 2012 C7 kit with 06E103547AC. Built in May 2012 or later: the C7 and 4L Q7 kit with 06E103547AK.
Why doesn't the CREC kit include a heater pipe?
CREC engines do not use the plastic heater pipe found on Gen 1 engines. The CREC kit gets CREC-specific parts instead, including the 06E103547AF PCV valve, 06E129717F lower intake gaskets and 06E998907F injector seals.
Can I install an under supercharger kit myself?
If you are comfortable with cooling and intake work, yes. Owners report roughly 4 to 8 hours depending on experience and help. Otherwise, a qualified independent Audi shop can do it in one visit.
Bottom Line
The supercharger only has to come off once if you bring the right box to the job. Match your car to its PCV valve, grab the kit built around it, and add the check valves and tensioner pulley while the valley is open. For a B8.5 S4, S5, Q5 or SQ5, that is the B8.5 Audi 3.0T under supercharger kit, and the table covers everyone else. Pay the labor once and keep the rest of the Audi Tax in your pocket.
Get the B8.5 Under Supercharger Kit, $649.99
Drive the difference. Drive Vorsprung.
Prices checked November 2, 2026 and subject to change. Labor figures are owner-reported or typical shop quotes.

