Pulling the supercharger on an Audi 3.0T is a rite of passage. Thermostat, water pump, PCV valve, porting: sooner or later the blower comes off, and when it goes back on, the seals underneath decide whether you fixed your car or bought yourself a vacuum leak. This guide to Audi 3.0T supercharger gasket replacement covers the leak signs, the Gen 1 and CREC part numbers and what else to swap while you're in there. Short version? Never reuse the old seals, and start with our 3.0T intake manifold gasket set for the S4, S5, A6, A7 and Q7.
What "Supercharger Gaskets" Means on the 3.0T
The supercharger and its two charge air coolers come off as one assembly. Audi's repair manual literally says to "lift off supercharger with charge air coolers." Below that, two joints seal the air path to the cylinders, plus one small tube:
- ✅ Six upper gaskets (079129717D) seal the supercharger to the intake manifold bottom sections. They're disturbed every time the supercharger comes off.
- ✅ Six lower gaskets seal each bottom section to its cylinder head: 079129717B on Gen 1 and 06E129717F on CREC, per our kit parts lists. They're disturbed only when a bottom section comes off, which owners report for the PCV valve and Audi requires for the injectors.
- ✅ The 06E103213 vent tube links the PCV assembly in the valley to the bottom of the supercharger. Our 06E103213 vent tube replacement is $5.99.
Audi's manual says to renew seals and gaskets, and its exploded view of the bottom section marks the intake manifold gasket "Renew." Translation: new gaskets every time. (A supercharger rebuild, with its internal seals, is a different job.)
Signs Your Supercharger Gaskets Are Leaking
B8 S4 owners who log boost see vacuum at idle and when coasting, and boost only under load. So a bad seal under the supercharger can cause idle trouble, power trouble or both:
- ✅ A rough, surging or hunting idle, especially right after supercharger work.
- ✅ Lean codes such as P0171 or P0174. The engine computer adds fuel to cover the extra air until the correction runs out of room.
- ✅ Misfires or a stumble at idle.
- ✅ A hiss or whistle that changes pitch with the throttle.
- ✅ A soft pull under load and worse fuel economy.
A torn PCV diaphragm sets the same lean codes and lives under the same supercharger. One code reference for the 3.0T Q7 ranks it the most likely cause of P0174 and points to the intake manifold gaskets when only one bank is lean. Our Audi 3.0T PCV valve replacement guide covers that side. Losing coolant too? Start with our intercooler leak symptoms and 3.0T coolant leak guides instead.
Shops prove a leak with a smoke or pressure test of the intake. And if trouble started right after a teardown, check the obvious: one B8 S4 owner chased a hunting idle and a P050A code after a thermostat and water pump job, pulled the supercharger twice, then found the short PCV pipe from under the blower lying on the ground.
What to Look for in a Supercharger Gasket Set
- ✅ Both layers in one box. Uppers are the must-have, but if a bottom section comes off, you want the lowers on the bench, not on backorder.
- ✅ The right lower gasket. Gen 1 and CREC lowers differ, and our CREC vs Gen 1 guide shows how to tell which you have.
- ✅ A material for your climate. A factory-style rubber compound does the job; low-temperature Viton GLT is the upgrade for cold winters.
- ✅ The vent tube. It's the part most likely to get cracked, lost or forgotten.
- ✅ Fitment help from humans. Audi changed part numbers over the 3.0T's life, so a VIN check beats guessing.
Our Gasket Sets vs Typical Name-Brand Gaskets vs the Dealer
Here's the math. Our standard 3.0T supercharger gasket set is $34.99 and the GLT TruSeal set is $49.99, and each covers the upper and lower runner gaskets in one order. Typical name-brand gaskets run roughly $3 to $6 apiece at big online retailers, sold one part number at a time. Audi dealer parts sites list the Gen 1 lower (079129717B) at $18.68 each and the CREC lower (06E129717F) at $39.19 each, so six CREC lowers top $235 before you buy a single upper. That's the Audi Tax, in rubber form.
| Vorsprung standard set | Vorsprung GLT TruSeal set | Typical name-brand gaskets | Genuine Audi from the dealer | |
|---|---|---|---|---|
| Price | $34.99 for the set | $49.99 for the set | About $3 to $6 per gasket, sold one at a time | $18.68 each for a Gen 1 lower, $39.19 each for a CREC lower |
| Material | Factory-style rubber compound | Viton GLT, rated -40°F to +400°F | Factory-style | Factory part |
| Coverage | Upper and lower runner gaskets | Same coverage as the standard set | You count and match the part numbers | One part number at a time |
| Fitment help | VIN check by email | VIN check by email | Varies by retailer | Dealer parts counter |
The standard set costs about what a dozen name-brand singles would, with the counting done for you. Ready to reseal it once? Grab the Audi 3.0T intake manifold gasket set.
Shop the 3.0T Intake Manifold Gasket Set, $34.99
✅ Viton GLT upgrade, plus Elring, Hengst and Graf in our kits · ✅ Fitment help by VIN at help@vorsprungautowerk.com · ✅ Free US shipping on orders over $425
What's in Our Sets and Why
The standard set ($34.99) is the do-it-once baseline: upper and lower runner gaskets engineered to OEM specifications and built for the 3.0T's heat cycles. Pick it when you just need fresh 3.0T supercharger gaskets that fit.
The GLT TruSeal intake manifold gasket set ($49.99) keeps the same fit and coverage in Viton GLT, a peroxide-cured, low-temperature fluoroelastomer. Per the listing, it stays flexible down to -40°F, is rated to +400°F, resists blow-by gases, oil vapor and fuel vapor, and is molded to the factory 079129717B, 079129717D and 06E129717 profiles. Real winters? This is your set.
The 06E103213 vent tube ($5.99) cross-references the factory part. Hard, cracked or missing? Swap it while everything is apart.
What Else to Replace While the Supercharger Is Off
Gaskets are rarely the reason the supercharger comes off. The reason lives in the valley. Every one of our under supercharger kits bundles the billet thermostat housing and thermostat, a Graf metal water pump, the correct OE PCV valve, upper and lower intake manifold gaskets, the vent tube and an injector seal kit, plus a metal heater pipe on Gen 1 kits. Coming off for any of those? Buy the kit.
For a B8.5 S4, S5, Q5 or SQ5, that's our B8.5 under supercharger kit (from $649.99), with a GLT TruSeal gasket option for $25 more. Other cars can use our under supercharger kit chooser or browse every Audi 3.0T under supercharger kit.
- ✅ The belt tensioner. The belt is already off, so swap the factory plastic tensioner pulley for our billet supercharger tensioner pulley ($64.99, or $111.99 with an OEM tensioner).
- ✅ Porting. The blower is already on your bench. Our ported supercharger guide explains the options.
- ✅ Injector seals. Audi's injector procedure starts with the supercharger and the bottom section, so this is the cheapest time. See our 3.0T injector seal guide.
- ✅ Charge air cooler seals. A separate set, needed only if the coolers come out of the supercharger.
Fitment: Which Gaskets Your 3.0T Uses
All of our under supercharger kits use the same six upper gaskets (079129717D). The lowers split by generation:
- ✅ Gen 1 EA837, lower gasket 079129717B: 2010 to 2012 B8 S4, 2010 to 2012 S5 Cabriolet (the coupe had the 4.2 V8) and 2009 to 2011 C6 A6 (B8 and C6 kit); 2013 to 2016 B8.5 S4, 2013 to 2017 S5, 2013 to 2017 Q5 3.0T, 2014 to 2017 SQ5 and 2013 to 2014 A8 (B8.5 kit); 2012 A6 and A7 built before May 2012 (early 2012 C7 kit); C7 A6 and A7 built from May 2012 through 2015 and the 2011 to 2015 4L Q7 (C7 A6, A7 and 4L Q7 kit).
- ✅ CREC, lower gasket 06E129717F: 2016 to 2018 C7.5 A6 and A7, 2015 to 2018 A8 and 2017 to 2019 4M Q7 (Gen 2 CREC kit).
Buying gaskets alone? The standard intake manifold gasket set lists the B8 and B8.5 S4 and S5, SQ5, C7 and C7.5 A6 and A7 and 4L and 4M Q7; the GLT set adds the Q5 3.0T and D4 A8. Because CREC lowers are a different part, CREC owners should email a VIN first, as should anyone whose car isn't listed. The vent tube lists the B8 S4, S5 Cabriolet, 8R Q5 and D4 A8.
Install Notes: Time, Tools and Tips
Swapping gaskets is easy. Getting the supercharger off is the job. In one long-running DIY thread, an owner and a helper needed about 8 hours the first time (6 or less the next), a seasoned DIYer said about 2 hours for a thermostat, and another member posted a dealer quote of $1,356 with 6.5 hours of labor for the thermostat job. First time? Budget a full day.
Tools: Torx and triple-square bits, a torque wrench, port plugs or clean rags, a marker for vacuum hoses and a thread tap. Doing the water pump? Add the pin wrench that holds its pulley.
- ✅ Plug every opening as soon as the supercharger is off, as Audi's procedure says.
- ✅ Remove every trace of old gasket, and keep oil and grease off hose connections and air pipes.
- ✅ Chase the threaded holes with a tap before the bolts go back in.
- ✅ Seat the vent tube before the supercharger goes down. The manual's reminder to check the crankcase breather connection is there for a reason.
- ✅ Torque to factory values in the factory sequence. No gorilla.
- ✅ After the first start, check for fuel and coolant leaks and listen on a test drive. Idle or lean-code drama means a smoke test before the blower comes off again.
Audi 3.0T Supercharger Gasket FAQ
Do I need new supercharger gaskets every time the supercharger comes off?
Yes. Audi's repair manual says to renew the seals and gaskets, and reusing flattened seals to save about $35 on a job that takes hours of labor is a bad trade.
How do I know if my supercharger gaskets are leaking?
Watch for a rough or hunting idle, lean codes such as P0171 or P0174, misfires, a hiss that changes with the throttle or a soft pull under load. Confirm it with a smoke or pressure test, and rule out the PCV valve, which sets the same codes.
How much does Audi 3.0T supercharger gasket replacement cost?
Parts are cheap: $34.99 for our standard set or $49.99 for GLT TruSeal. Labor is the big number, because the supercharger has to come off. One owner posted a dealer quote of $1,356 with 6.5 hours of labor for a thermostat job, which needs the same removal.
Are Gen 1 and CREC supercharger gaskets the same?
The six upper gaskets are the same part (079129717D) in our Gen 1 and CREC kits. The lowers differ: 079129717B on Gen 1 and 06E129717F on CREC.
Is the GLT TruSeal set worth $15 more?
If you see real winters or plan to keep the car for years, yes. Per the listing, Viton GLT stays flexible down to -40°F and is rated to +400°F, while the standard set uses a factory-style rubber compound.
What is the small tube under the supercharger?
That's the 06E103213 vent tube, the short pipe between the PCV assembly and the bottom of the supercharger. It's easy to crack, lose or forget, and a missing one can leave you chasing a hunting idle. Ours is $5.99.
The Bottom Line
Supercharger gaskets are the cheapest part of any 3.0T valley job and the easiest way to turn a fix into a comeback. Replace the uppers every time, keep the right lowers on the bench, don't lose the vent tube, and if the thermostat or PCV valve is coming out, buy the kit. Gaskets only? Grab the Audi 3.0T supercharger gasket set and reseal it once.
Get the Audi 3.0T Supercharger Gasket Set, $34.99
Drive the difference. Drive Vorsprung.
Prices checked November 10, 2026 and subject to change. Labor times and costs are owner-reported or typical shop quotes.

