Audi 3.0T Tech Guides & News

Audi A8 3.0T Upgrades: The Right Mod Order for the Supercharged D4 A8, Gen 1 and CREC (2013 to 2018)

Vorsprung under supercharger kit for Audi A8 3.0T upgrades, fits the 2013 to 2014 D4 A8 Gen 1 supercharged 3.0T

Shopping for Audi A8 3.0T upgrades? Your flagship hides the same supercharged V6 as the B8.5 S4, C7 A6 and Q7, so the parts exist. The catch: 2013 to 2014 cars and 2015 to 2018 cars run two different versions of that engine, and the parts that fail live under the supercharger. Get the order wrong and you pay for the same labor twice. For a 2013 to 2014 A8, the smart first move is our Gen 1 under supercharger kit for the A8 3.0T. Here is the order for both.

Gen 1 or CREC: Which A8 3.0T Do You Have?

Every US D4 A8 3.0T is supercharged, but Audi changed the engine for 2015. Our listings split them:

  • ✅ 2013 to 2014, Gen 1 EA837: direct injection only, a supercharger that is always driven, and PCV valve 06E103547AH, the same valve as the B8.5 S4.
  • ✅ 2015 to 2018, CREC (often called D4.5): port plus direct injection, a supercharger with a magnetic clutch, and PCV valve 06E103547AF, shared with the C7.5 A6 and 4M Q7.
  • ✅ 2019 and newer, D5: a turbocharged 3.0T. Nothing in this guide fits it.

Not sure which one is in your garage? The 2015 A8 owner's manual puts the vehicle data label, engine code included, in the spare wheel well. The 10th VIN character gives the model year: D is 2013, E is 2014, F through J cover 2015 to 2018, and K is 2019. Near a changeover, the engine code wins, so email your VIN to help@vorsprungautowerk.com if in doubt. Our CREC vs Gen 1 guide and 3.0T supercharged engine guide go deeper.

Which A8 3.0T path is yours? VIN year D or E: Gen 1 parts. F through J: CREC parts. K or later: turbo D5, no fit. WHICH A8 3.0T PATH IS YOURS? Check VIN character 10 and the engine code Data label: spare wheel well or service booklet D or E: 2013 to 2014 Gen 1 EA837 F, G, H or J: 2015 to 2018 CREC, often called D4.5 K or later: 2019 on D5 A8, turbo 3.0T 1 2 3 PCV 06E103547AH Gen 1 kit (B8.5 kit) Gen 1 street port PCV 06E103547AF CREC kit, CREC port Clutch delete: tune needed EA839 turbo V6 These supercharged parts do not fit Label and year disagree? Trust the engine code. SCHEMATIC ONLY, NOT TO SCALE.
Model year gets you close. The engine code on the data label settles it.

Audi A8 3.0T Upgrades in the Right Order

Anything under the supercharger goes first, because the blower should only come off once. Then add boost, then airflow, then the parts that hold the engine still. This is the A8 version of our 3.0T upgrade path.

Step 2013 to 2014 A8 (Gen 1) 2015 to 2018 A8 (CREC) Tune needed (per listing)
1. Valley service Gen 1 kit (06E103547AH) plus a billet tensioner pulley Gen 2 CREC kit (06E103547AF) plus the same tensioner pulley None listed
2. Pulley and throttle body TruDrive crank pulley, 84mm throttle body kit Same parts, after the clutch decision Pulley: none required just to install, log it. 84mm kit: yes
3. Porting Gen 1 street port CREC street port Have your tuner confirm the file covers the airflow
4. Exhaust HEH Headers V2 HEH Headers V2 Not for headers alone, recommended when stacked
5. Mounts DynaCore 65A mounts DynaCore 65A mounts (VIN check) No

Step 1: Fix the Valley Before You Add Boost

Audi built a luxury sedan that started at $73,095 in 2013, then cooled its V6 through a plastic thermostat housing tucked under the supercharger. That is Audi Tax with a side of irony. The housing, PCV valve, water pump and intake manifold gaskets are the usual suspects on every supercharged 3.0T. Watch for:

  • ✅ Coolant level dropping with no puddle, or a sweet smell after a drive
  • ✅ Rough idle, a whistle at idle or lean codes, classic PCV and vacuum leak signs
  • ✅ An oil smell under the hood

Diagnosis lives in our coolant leak guide and PCV valve replacement guide. In a kit, look for:

  • ✅ The right PCV valve: 06E103547AH or 06E103547AF
  • ✅ A billet, not plastic, thermostat housing and a metal water pump
  • ✅ Both gasket sets plus injector seals, reachable only with the blower off

Vorsprung billet thermostat housing with thermostat and hardware from the under supercharger kit for the 2013 to 2014 Audi A8 3.0T

Two more checks first. On a 2015 to 2018 car, run the VIN through NHTSA's recall lookup: recall 19V-035 (Audi 24DP) covers certain 2015 to 2018 A8s, and dealers replace both fuel rails free because they may leak fuel. On a 2013 to 2014 car, which is direct injection only, intake valve carbon is worth a look; one owner reports a walnut-blast quote of about $1,000. And while the belt is off, swap the factory plastic tensioner pulley for our billet supercharger tensioner pulley ($64.99 pulley only, $111.99 on a new OEM tensioner).

Under Supercharger Kits Compared: Ours vs Name-Brand vs the Dealer

Both A8 kits start at $649.99 with a billet thermostat housing plus Graf, Hengst and Elring parts. Typical name-brand kits with a similar parts list were listed at roughly $815 to $865 at major retailers when we checked, before sales. The dealer route means genuine parts priced one at a time, the plastic housing again, and labor owners report at about 5 billed hours for the thermostat alone.

Vorsprung A8 kits Typical name-brand kits Dealer, part by part
Starting price $649.99, Gen 1 or CREC About $815 to $865 list Each part priced separately, plus labor
Thermostat housing Billet aluminum, thermostat included Aluminum thermostat assembly Factory plastic housing
Water pump Graf metal pump Graf metal pump Genuine pump
PCV valve Hengst, 06E103547AH or AF Hengst Genuine Audi
Gaskets and injector seals Elring, 6 upper, 6 lower, 6 injector seal kits Elring gaskets, same counts Bought one at a time

Same OE-supplier parts, billet instead of plastic, and money left over for step 2. Start with the A8 3.0T under supercharger kit for 2013 to 2014 cars or its twin, the Gen 2 CREC kit for 2015 to 2018 cars.

Shop the 2013 to 2014 A8 Kit, $649.99

✅ Graf, Hengst and Elring parts in both A8 kits  ·  ✅ Fitment help by VIN at help@vorsprungautowerk.com  ·  ✅ Free US shipping on orders over $425

What's in Our A8 Kits and Why

Pulling and refitting the supercharger is the expensive part, so both kits replace everything that lives under it:

Part 2013 to 2014 A8 kit (Gen 1) 2015 to 2018 A8 kit (CREC)
Thermostat housing Billet with thermostat, replaces 06E121111AL Billet with thermostat, replaces 06E121111AT
Water pump Graf metal, replaces 06E121018N Graf PA1228 metal
PCV valve Hengst 06E103547AH Hengst 06E103547AF
Intake manifold gaskets Elring 079129717D and 079129717B, 6 each Elring 079129717D and 06E129717F, 6 each
Injector seals Elring 06E998907E, x6 Elring 06E998907F, x6
Heater pipe Aluminum, replaces plastic 06E121065N Not used on CREC
PCV to supercharger pipe Genuine 06E103213 Genuine 06E103213

Both kits offer a coolant add-on, and the Gen 1 kit a GLT TruSeal gasket upgrade (+$25).

Vorsprung Gen 2 CREC under supercharger kit for the 2015 to 2018 Audi A8 3.0T: billet thermostat housing, Graf water pump, Hengst PCV valve and Elring gaskets

Step 2: Pulley and Throttle Body

With the valley sorted, add boost. The TruDrive crank pulley ($224.99 to $296.99, rings from 179mm to 207mm) lists the D4 A8. Its listing says no dedicated tune is required just to install it, but recommends logging or having your tuner confirm fueling and knock. The 84mm throttle body upgrade kit ($349.99 with the VDO throttle body) lists the 2013 to 2018 A8, and its listing says you need a tune. Deep dives: crank pulley sizes and 84mm throttle body options.

CREC owners get one extra homework item: the supercharger clutch. Owners report factory clutches slipping or failing at higher power, so read our CREC supercharger clutch delete guide first. The billet clutch delete ($179.99, pre-order with stock due late November 2026) requires a tune, per its listing.

TruDrive 193mm crank pulley for the Audi A8 3.0T supercharged D4, aluminum ring on a stainless hub

Step 3: Port the Supercharger

A ported case moves more air at the same pulley, so pair it with step 1 while the blower is off. The Gen 1 street port covers 2013 to 2014 A8s from $749.99 with your core. The CREC street port covers 2015 to 2018 cars from $999.99 with your core, because CREC cases need extra machine work. Both come back in about 2 weeks, and both listings say there is no separate ported supercharger tune: have your tuner confirm the file covers the extra airflow. More in our ported supercharger guide.

Step 4: Exhaust

The HEH Headers V2 list the D4 A8: equal-length 321L stainless headers that replace the factory manifold and test pipe section, with the Dual Layer heat shield version at $1,999.99. The listing says headers alone don't require a dedicated tune, but recommends one when you stack them with porting or a pulley. Browse the D4 A8 exhaust parts and read our 3.0T headers guide first.

For off-road and competition use. Check your local emissions and inspection rules before modifying your exhaust.

Step 5: Engine Mounts

Add power and tired fluid-filled mounts let the engine rock. The DynaCore 65A engine mounts ($249.99 a pair, marked down for cosmetic blems) list the D4 A8 3.0T, include an emulator for cars with active mounts, and need no tuning, per the listing. It names the D4 A8 without years, so email your VIN for a 2015 to 2018 car. More in our engine mounts guide.

Fitment: Which A8 Gets Which Part

The Gen 1 kit fits the 2013 to 2014 A8 3.0T, plus the B8.5 S4, S5, Q5 and SQ5. The Gen 2 CREC kit fits the 2015 to 2018 A8 quattro 3.0T, plus the 2016 to 2018 A6 and A7 and the 2017 to 2019 Q7. Porting follows the same split, the clutch delete is CREC only, and the pulley, 84mm kit, tensioner and headers list the D4 A8 across both engines. The long-wheelbase A8 L 3.0T shares the engine and the split. Everything we sell for the car lives in the D4 A8 3.0T performance parts collection, and C7 owners can compare notes in our A6 and A7 3.0T upgrades guide.

Install Notes

  • ✅ Time: owners report dealers billing about 5 hours for the 3.0T thermostat alone, and one detailed DIY write-up took 8 hours with two people the first time.
  • ✅ Tools: a pin wrench for the coolant pump pulley, bung plugs for the open charge air ports, hose clamps and a helper to lift the supercharger.
  • ✅ Tips: mark every vacuum hose and connector, lube O-rings with coolant, and bleed per the factory steps quoted in that write-up: 2,000 rpm to push coolant into the supercharger and heater core, then the level at MAX cold.

Audi A8 3.0T Upgrades FAQ

Is the Audi A8 3.0T supercharged or turbocharged?

Every 2013 to 2018 D4 A8 3.0T sold in the US is supercharged. The 2019 and newer D5 A8 switched to a turbocharged 3.0T, so the supercharged parts in this guide do not fit it.

How do I tell if my A8 has the CREC engine?

Read the engine code on the vehicle data label in the spare wheel well. Our listings put 2013 to 2014 cars on Gen 1 and 2015 to 2018 cars on CREC. If label and year disagree, trust the label and email your VIN to help@vorsprungautowerk.com.

Do S4 or A6 parts fit the A8 3.0T?

Many valley parts do, because it is the same supercharged V6. The 2013 to 2014 A8 shares its 06E103547AH PCV valve and kit with the B8.5 S4, and the 2015 to 2018 A8 shares its CREC kit with the 2016 to 2018 A6 and A7 and 2017 to 2019 Q7. Exhaust and mounts are more chassis specific, so check each fitment table.

Do A8 3.0T upgrades need a tune?

Per our listings, the DynaCore mounts need no tuning, and the kits and tensioner pulley list none. The TruDrive pulley needs no dedicated tune just to install, but log fueling and knock. The 84mm kit and CREC clutch delete need a tune. After porting, your tuner should confirm the file covers the extra airflow, and headers only call for a tune when stacked with other mods.

How much does the under supercharger job cost on an A8 3.0T?

Our kits start at $649.99 for either engine. Labor is the big variable: owners report dealers billing about 5 hours for the thermostat alone, and owners of other 3.0T models report independent shop quotes around $2,700 to $2,800 for the PCV, thermostat and water pump plus related hoses.

Is there a recall to check on a 2015 to 2018 A8?

Yes. Recall 19V-035 (Audi 24DP) covers certain 2015 to 2018 A8s, and dealers replace both fuel rails free because they may leak fuel. Run your VIN through NHTSA's recall lookup before you start modifying.

Bottom Line

The best Audi A8 3.0T upgrades start under the supercharger. Do the valley once with the under supercharger kit for the 2013 to 2014 A8 or the CREC kit for 2015 to 2018, then stack pulley, throttle body, porting, exhaust and mounts in that order. Your A8 keeps its limo manners. It just stops apologizing for having six cylinders.

Shop the 2015 to 2018 A8 CREC Kit, $649.99

Drive the difference. Drive Vorsprung.

Prices checked November 11, 2026 and subject to change. Labor figures are owner-reported or typical shop quotes.

Previous
Audi 3.0T Supercharger Gasket Replacement: Leak Signs, Part Numbers and What Else to Replace (S4, S5, Q5, SQ5, A6, A7, A8, Q7)
Next
Audi S4 Wheel Hop: Why Your B8 Hops on Launch, What It Can Break and the Billet Insert Fix (B8 and B8.5 S4, S5, SQ5)